HP ProLiant DL380e User Manual Download | Manualshive

Page: 111 / 155

background image

RBSU menu (HP ProLiant G6 and earlier servers or server blades) 111

•

In the OS Control Mode, processors operate at maximum speed unless the OS enables a power

management policy.

USB External Port Capability

The USB External Port Capability option configures the USB external ports to operate at USB 1.1 or USB
2.0 speeds.
Select USB 2.0 for improved performance if using an operating system other than Microsoft® Windows
Server® 2003 or Microsoft® Windows Server® 2003 x64.

NOTE:

Running external USB ports at USB 2.0 with Microsoft® Windows Server® 2003 or

Microsoft® Windows Server® 2003 x64 causes delays during installations.

«
...
109
110
111
112
113
...
»

Summary of Contents for ProLiant DL380e




























































































































































Reviews:

No comments

Related manuals for ProLiant DL380e

D DPH-50U DPH-50U

Brand: D-Link Pages: 2

AirPlus DWL-810

Brand: D-Link Pages: 64

Brand: D-Link Pages: 39

Brand: D-Link Pages: 8

802.11g Wireless LAN USB Adapter DWL-G122

Brand: D-Link Pages: 43

AirPlusXtremeG DWL-G650

Brand: D-Link Pages: 20

Brand: Conrad Pages: 4

Brand: Origaudio Pages: 1

Brand: BIG ASS FANS Pages: 56

Brand: R&S Pages: 66

Brand: Goobay Pages: 10

VERDEdri 17-10504K

Brand: World Dryer Pages: 8

EZ Connect SMC2662W

Brand: SMC Networks Pages: 62

USB2-F-7 01 Series

Brand: Connective Peripherals Pages: 3

Brand: NCR Pages: 10

Brand: D-Link Pages: 50

Brand: Asante Pages: 60

CURV 500 Series

Brand: LD Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands