HP ProLiant DL380e User Manual Download | Manualshive

Page: 105 / 155

background image

RBSU menu (HP ProLiant G6 and earlier servers or server blades) 105

IMPORTANT:

Menu options may differ from those in this document, depending on specific

server options.

Embedded Serial Port A

The Embedded Serial Port A option sets the configuration for the internal serial port A. The settings include
the address and IRQ. This option can also disable the port.

NOTE:

Embedded Serial Port options may be named Embedded COM Port options,

depending on the server.

Embedded Serial Port B

The Embedded Serial Port B option sets the configuration for the internal serial port B. The settings include
the address and IRQ. This option can also disable the port.

NOTE:

Embedded Serial Port options may be named Embedded COM Port options,

depending on the server.

«
...
103
104
105
106
107
...
»

Summary of Contents for ProLiant DL380e




























































































































































Reviews:

No comments

Related manuals for ProLiant DL380e

Brand: Rainforest Automation Pages: 29

Brand: Tactic Pages: 4

Brand: GRAS Pages: 6

Brand: P.I. Engineering Pages: 4

Powerline PL1200

Brand: NETGEAR Pages: 12

Brand: Nvidia Pages: 62

Brand: Rosewill Pages: 12

Enercell 273-356

Brand: Enercell Pages: 1

Brand: Planet Pages: 72

Brand: Emulex Pages: 19

Brand: 7inova Pages: 36

Brand: Targus Pages: 8

HandyPort-Serial HPS-120

Brand: HandyWave Pages: 11

USB Analog TV Stick II

Brand: KWorld Pages: 10

Brand: D-Link Pages: 7

Brand: D-Link Pages: 30

Brand: D-Link Pages: 25

DUB-9240 - UWB Wireless USB

Brand: D-Link Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands