HP ProLiant DL380e User Manual Download | Manualshive

Page: 112 / 155

background image

RBSU menu (HP ProLiant G6 and earlier servers or server blades) 112

This selection does not affect the internal USB port or USB iLO2 Virtual Media devices.

Ultra Low Power State

Ultra Low Power State enables the system to transition to the lowest processor power state when the Power

Regulator Mode is configured for HP Static Low Power Mode or HP Dynamic Power Savings Mode. In HP
Static Low Power Mode, power savings increases with a small impact on maximum system performance.
HP Dynamic Power Savings Mode increases power savings when processor utilization is low.

Ultra Low Power State is supported only on HP ProLiant servers with AMD processors.

«
...
110
111
112
113
114
...
»

Summary of Contents for ProLiant DL380e




























































































































































Reviews:

No comments

Related manuals for ProLiant DL380e

Brand: Panasonic Pages: 8

Brand: cable matters Pages: 2

Brand: cable matters Pages: 12

Brand: cable matters Pages: 2

Brand: Paradyne Pages: 5

Brand: Paradyne Pages: 14

Brand: Qlogic Pages: 8

Brand: Renesas Pages: 18

Carlyle Tools 791-7136

Brand: Napa Pages: 13

Magic I/O EV-170

Brand: Everex Pages: 40

Brand: BASETech Pages: 6

Portico TVA Series

Brand: Citel Pages: 109

Brand: Diamond Multimedia Pages: 14

Brand: ACTiSYS Pages: 8

Brand: Macally Pages: 14

Brand: Allen-Bradley Pages: 4

Brand: Zenisu Keisoku Pages: 14

Brand: ReSound Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands