HP ProLiant DL380e User Manual Download

Page: 122 / 155

RBSU menu (HP ProLiant G6 and earlier servers or server blades) 122

BIOS Serial Console Baud Rate

The BIOS Serial Console Baud Rate option enables baud rate changes.

EMS Console

The EMS Console option is a Microsoft® Windows Server® 2003 feature that allows for emergency

management console to be redirected through the serial port. When using iLO, select the value (COM 1
or COM 2) assigned to the Virtual Serial Port (on page

106

). When redirecting EMS through a physical

serial port, select the value assigned to the Embedded Serial Port ("

Embedded Serial Port A

" on page

105

). The EMS Console feature is disabled by default.

Summary of Contents for ProLiant DL380e




























































































































































Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands

HP ProLiant DL380e, User Manual

Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands