HP ProLiant DL380e User Manual Download

Page: 9 / 155

RBSU menu (HP ProLiant G7 servers or server blades) 9

RBSU menu (HP ProLiant G7 servers or server
blades)

RBSU menu overview

The RBSU menu lists configuration settings to view or modify.

IMPORTANT:

Menu options may differ from those in this document, depending on specific

server options.

On the right-hand side of the screen, a window displays basic server information, including the server
model, serial number, BIOS version, backup BIOS version, memory installed, and processors installed.

NOTE:

A service number is reported below the serial number on the HP ProLiant DL760

Server only.

NOTE:

Pressing the F1 key when any sub-menu option is highlighted allows you to view a

description of that feature. Please note that all menus are in English only.

Summary of Contents for ProLiant DL380e




























































































































































Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands

HP ProLiant DL380e, User Manual

Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands