HP ProLiant DL380e User Manual Download

Page: 103 / 155

RBSU menu (HP ProLiant G6 and earlier servers or server blades) 103

RBSU menu (HP ProLiant G6 and earlier servers
or server blades)

RBSU menu overview

The RBSU menu lists configuration settings to view or modify.

IMPORTANT:

Menu options may differ from those in this document, depending on specific

server options.

On the right-hand side of the screen, a window displays basic server information, including the server
model, serial number, BIOS version, backup BIOS version, memory installed, and processors installed.

NOTE:

A service number is reported below the serial number on the HP ProLiant DL760

Server only.

NOTE:

Pressing the F1 key when any sub-menu option is highlighted allows you to view a

description of that feature. Please note that all menus are in English only.

Summary of Contents for ProLiant DL380e




























































































































































Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands

HP ProLiant DL380e, User Manual

Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands