HP ProLiant DL380e User Manual Download

Page: 114 / 155

RBSU menu (HP ProLiant G6 and earlier servers or server blades) 114

Standard Boot Order (IPL)

The Standard Boot Order (IPL) option configures the Initial IPL device and controls the search order the
server uses to look for a bootable device.

NOTE:

If you enable or disable a device, restart the server. Changes do not take effect until

after reboot.

Boot Controller Order

The Boot Controller Order option selects which of the installed mass storage devices is used as the

primary boot controller. The server attempts to power up with the OS on this device.
The primary boot controller is set to controller 1.

NOTE:

Changes made to the Boot Controller Order in the ORCA Utility are reflected in this

menu.

Summary of Contents for ProLiant DL380e




























































































































































Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands

HP ProLiant DL380e, User Manual

Search results

Summary of Contents for ProLiant DL380e

Reviews:

Related manuals for ProLiant DL380e

Brands by name

Popular brands