HP ProLiant DL380e User Manual Download | Manualshive

Page: 78 / 155

background image

RBSU menu (HP ProLiant G7 servers or server blades) 78

To further optimize the system, HP recommends updating these boot drivers to the latest versions after the
OS installation. This functionality is not available with Microsoft® Windows Server® 2008.

PCI Bus Padding Options (G7 servers)

This option allows the user to disable the default PCI Bus padding where each expansion slot is provided
with an extra PCI Bus number. By default, the System ROM pads bus numbers for slots such that adding

expansion cards does not affect the bus numbering of devices in the system. Disabling this option works
around issues with certain expansion cards.

«
...
76
77
78
79
80
...
»

Summary of Contents for ProLiant DL380e




























































































































































Reviews:

No comments

Related manuals for ProLiant DL380e

D DPH-50U DPH-50U

Brand: D-Link Pages: 2

AirPlus DWL-810

Brand: D-Link Pages: 64

Brand: D-Link Pages: 39

Brand: D-Link Pages: 8

802.11g Wireless LAN USB Adapter DWL-G122

Brand: D-Link Pages: 43

AirPlusXtremeG DWL-G650

Brand: D-Link Pages: 20

Brand: Zonet Pages: 63

Brand: D-Link Pages: 1

Brand: Tektronix Pages: 2

Brand: Vantec Pages: 4

TravelCharge Companion HT 3.4

Brand: Wagan Pages: 16

Brand: Goobay Pages: 5

SNG 12/1500-OW-N

Brand: VOLTCRAFT Pages: 4

Brand: Hamlet Pages: 4

Brand: Radio Shack Pages: 2

Brand: Aaronn Pages: 2

Wireless LAN Game Adapter W11

Brand: Hama Pages: 4

Brand: Tailwind Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands