HP ProLiant DL380e User Manual Download | Manualshive

Page: 146 / 155

background image

RBSU configuration flow 146

RBSU configuration flow

RBSU configuration flow overview

RBSU can be used in two ways to configure a server: a manual flow and a scripted installation flow for

working with SmartStart software. Each method has its own flow of procedures. This information is of a
technical nature and intended for reference purposes only.

Manual path flow

NOTE:

Manual Path Flow does not apply for servers with an integrated ATA RAID IDE

Controller.

NOTE:

Manual Path Flow is not necessary for servers with Embedded Server Setup.

RBSU can be used to configure an HP server without the use of SmartStart. When the server is powered

up in an unconfigured state, RBSU executes when the F9 key is pressed, allowing the server to be
configured. After the server has been configured using RBSU:

1.

Restart or power up the server.

2.

Press the

F8

key to execute ORCA.

3.

After the primary array controller has been configured with ORCA, restart the server.

4.

Install the operating system ("

Operating System Installation

" on page

138

). Install any necessary

applications as well.

«
...
144
145
146
147
148
...
»

Summary of Contents for ProLiant DL380e




























































































































































Reviews:

No comments

Related manuals for ProLiant DL380e

Brand: J5create Pages: 2

Brand: U.S. Boiler Company Pages: 20

Brand: HomeSpot Pages: 12

USB-IrDA Adapter

Brand: Hama Pages: 13

USB Power Adapter A04-PAU02

Brand: Atlantis Land Pages: 2

Brand: Hainbuch Pages: 108

Brand: Black Box Pages: 2

Brand: Teletronics International Pages: 2

Thunderbolt MTB3-002-HD

Brand: Tripp Lite Pages: 31

HandyPort HPU-120

Brand: HandyWave Pages: 19

AirStation WLI-USB-KB11

Brand: Buffalo Pages: 45

Brand: National Instruments Pages: 52

HomePlug AV 200

Brand: Gigaset Pages: 18

Brand: 7inova Pages: 36

Brand: ZyXEL Communications Pages: 95

Brand: YDI Pages: 28

Brand: Cambium Networks Pages: 1149

Brand: Sena Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands