HP ProLiant DL380e User Manual Download | Manualshive

Page: 53 / 155

background image

RBSU menu (HP ProLiant G7 servers or server blades) 53

Thermal Shutdown (G7 servers)

The Thermal Shutdown option is a toggle setting that determines when the server automatically powers
down due to dangerous temperatures. When the setting is enabled (default), the Advanced System
Management driver initiates a system shutdown when the temperature reaches approaches critical level.

When the setting is disabled, the Advanced System Management driver shuts down the system at the
critical level.

Wake-On LAN (G7 servers)

The Wake-On LAN option is a toggle setting that enables or disables the Wake-On LAN feature. When
set to Enabled, the server can be powered up remotely using a network controller. When changing to

Enabled, the following message appears:

«
...
51
52
53
54
55
...
»

Summary of Contents for ProLiant DL380e




























































































































































Reviews:

No comments

Related manuals for ProLiant DL380e

Brand: fafnir Pages: 16

Brand: Patton electronics Pages: 12

Brand: TEXIO Pages: 49

Brand: G-cluster Pages: 2

Brand: Gemtek Systems Pages: 20

Brand: ZNYX Pages: 13

Thunderbolt MTB3-002-HD

Brand: Tripp Lite Pages: 31

Brand: Lindy Pages: 16

NetBlaster ZX345

Brand: ZNYX Pages: 12

Brand: LM Technologies Pages: 27

Brand: StarTech.com Pages: 2

2208USB/ETH - annexe 1

Brand: SMC Networks Pages: 24

Brand: RCWARE Pages: 3

Brand: Hama Pages: 7

Brand: Fujitsu Pages: 97

PRIMEQUEST 2000 Series

Brand: Fujitsu Pages: 188

PRIMEQUEST 2000 Series

Brand: Fujitsu Pages: 734

FastStream SC 5300

Brand: ATTO Technology Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands