HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 196 / 232

background image

ENWW

HP Jetdirect Configuration Page 196

0C LAN ERROR -
RECEIVER OFF

There may be a problem with your network cabling or the
HP Jetdirect print server. Check the cabling and connectors
on your Ethernet network. If you cannot find a problem with
your network cabling, run the power-on self-test: turn the
printer off, then on again. If the error persists after the printer
is turned on again, there is a problem with the HP Jetdirect
print server.

0D LAN ERROR -
TRANSMITTER OFF

There may be a problem with your network cabling or the
HP Jetdirect print server. Check the cabling and connectors
on your Ethernet network. If you cannot find a problem with
your network cabling, run the power-on self-test: turn the
printer off, then on again. If the error persists, there is a
problem with the HP Jetdirect print server.

0E LAN ERROR -
LOSS OF CARRIER

Check the network connections. If the connections are
intact, run the power-on self-test: turn the printer off, then
on again. If the error persists, replace the HP Jetdirect
print server.

10 LAN ERROR -
UNDERFLOW

(Wired Ethernet) There may be a problem with your network
cabling or the HP Jetdirect print server. Check the cabling
and connectors on your network. If you cannot find a
problem with your network cabling, run the power-on
self-test: turn the printer off, then on again. If the error
persists, there is a problem with the HP Jetdirect print
server.

11 LAN ERROR -
RETRY FAULTS

(Wired Ethernet) There is a problem with your network
cabling or external network configuration. Verify operation
of the hub or switch port.

12 LAN ERROR -
NO LINKBEAT

With a 10/100 Base-TX port connected, this message is
displayed if Link Beat is not sensed. Check the network
cable, and verify that the concentrator/hub is providing Link
Beat.

13 NETWORK
RECONFIG - MUST
REBOOT

Reset or power off/on the HP Jetdirect print server to enable
new configuration values.

14 DISCONNECTED

The Novell NetWare protocol is disconnected. Check the
server and the print server.

15 CONFIGURATION
ERROR

(Ethernet) The configuration information for the NetWare
functions is not stored correctly on the HP Jetdirect print
server. Use the installation software, embedded Web
server, or other tools to reconfigure the print server. If this
error persists, there may be a problem with the HP Jetdirect
print server.

Table 9.9

Error Messages (2 of 10)

Error Code and
Message

Description

«
...
194
195
196
197
198
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Brand: Partner Pages: 9

Brand: TallyGenicom Pages: 145

T2265 SprintPro

Brand: Tally Pages: 217

Brand: TallyGenicom Pages: 12

Brand: Xerox Pages: 93

Brand: Xerox Pages: 36

Brand: Xerox Pages: 136

3250D - Phaser B/W Laser Printer

Brand: Xerox Pages: 6

Brand: Magicard Pages: 2

Brand: Magicard Pages: 2

Brand: I-O DATA Pages: 49

BladeCenter PN41

Brand: IBM Pages: 88

Brand: Sercomm Pages: 75

Brand: B&B Pages: 55

Brand: Posnet Pages: 2

SUPERSERVER 8045C-3R

Brand: Supermicro Pages: 118

Brand: Valcom Pages: 4

RS/6000 7043 260

Brand: IBM Pages: 322

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands