HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 203 / 232

background image

ENWW

HP Jetdirect Configuration Page 203

52 BAD BOOTP/DHCP
REPLY

An error was detected in the BOOTP or DHCP reply that the
HP Jetdirect print server received. The reply either had
insufficient data in the UDP datagram to contain the
minimum BOOTP/DHCP header of 236 bytes, had an
operation field that was not BOOTPREPLY(0X02), had a
header field that did not match the print servers hardware
address, or had a UDP source port that was not the
BOOTP/DHCP server port (67/udp).

53 BAD BOOTP
TAG SIZE

The tagsize in a vendor-specific field in the BOOTP reply
is either 0, or greater than the remaining number of
unprocessed bytes in the vendor-specified area.

54 BOOTP/RARP
IN PROGRESS

The HP Jetdirect print server is currently in the process of
obtaining its basic IP configuration information through
BOOTP/RARP.

55 BOOTP/DHCP
IN PROGRESS

The HP Jetdirect print server is currently in the process of
obtaining its basic IP configuration information through
BOOTP/DHCP, and has not detected any errors.

56 DHCP NAK

The HP Jetdirect print server received a negative
acknowledgement message from the DHCP server in
response to a configuration request.

57 UNABLE TO
CONNECT DHCP SVR

The HP Jetdirect print server had received IP parameters
from a DHCP server, but communication with the DHCP
server has been lost. Check status of the DHCP server.

If an infinite lease was assigned, the print server will use the
IP address of the most recent DHCP server used, but
operation may be degraded until a DHCP server responds.

58 POSTSCRIPT
MODE NOT
SELECTED

The printer does not support AppleTalk or AppleTalk
extensions.

59 INCOMPLETE F/W -
MUST DOWNLOAD

Firmware download message. Currently downloading
firmware to the HP Jetdirect print server, or the download
did not complete properly.

5A TURN PRINTER
OFF / ON

Firmware download message. Download of firmware is
complete. Power off/on the HP Jetdirect print server.

5C DHCP BAD REPLY

A bad reply was received from the DHCP server. Check your
DHCP server settings for this print server.

5D DHCP LEASE
DURATION TOO
SHORT

The DHCP lease times for this print server’s TCP/IP
configuration settings are too short. Reconfigure the DHCP
lease times on the DHCP server.

Table 9.9

Error Messages (9 of 10)

Error Code and
Message

Description

«
...
201
202
203
204
205
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Brand: Xyron Pages: 6

Brand: Xerox Pages: 2

Brand: Xerox Pages: 40

Brand: Xerox Pages: 69

Brand: Xerox Pages: 42

Brand: Omneon Pages: 2

NEAX2000 IVS Series

Brand: NEC Pages: 160

SimpliVity 2600 Gen10

Brand: HPE Pages: 37

Brand: Hawking Pages: 40

Express5800/320Fa-L

Brand: NEC Pages: 406

Brand: Xyplex Pages: 58

Brand: Xerox Pages: 214

Brand: Cardco Pages: 28

Perfecta 2400STP

Brand: Variquest Pages: 12

Server 3100 series

Brand: Digital Equipment Pages: 71

Brand: MHM Pages: 52

Brand: Daewoo Pages: 37

SC450NX - Server Platform - 0 MB RAM

Brand: Intel Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands