manualshive.com logo in svg

HP Jetdirect J7949e, Administrator'S Manual

The HP Jetdirect J7949e is a cutting-edge network print server that enables seamless connectivity between printers and networks. For easy and efficient setup, configuration, and troubleshooting, users can rely on the comprehensive Administrator's Manual, available for free download from our website. Enhance your printing experience today with this user-friendly manual. [Website]

Share
Download
background image

ENWW

HP Jetdirect Configuration Page 195

Error Messages

Error codes and messages that may appear in the Status sections 
of the Jetdirect configuration page are described in 

Table 9.9

. 

Table 9.9

Error Messages  (1 of 10)

Error Code and 
Message

Description

02 LAN ERROR - 
INTERNAL 
LOOPBACK

During self-test, the HP Jetdirect print server detected an 
internal loopback test error. The print server may be faulty. 
If the error persists, replace the HP Jetdirect print server.

03 LAN ERROR - 
EXTERNAL 
LOOPBACK

The HP Jetdirect print server is incorrectly connected to 
your network or is defective. Make sure your HP Jetdirect 
print server is correctly attached to your network. In addition, 
check the cabling and connectors. 

07 LAN ERROR - 
CONTROLLER CHIP

(Wired Ethernet) Check the network connections. If the 
connections are intact, run the power-on self-test: turn the 
printer off, then on again. If the error persists, replace the 
HP Jetdirect print server.  

07 AUTHENTICATION 
FAILED

The Jetdirect print server could not access the network 
because of an authentication error. The error depends on 
the authentication method used. 

Verify the authentication method and settings on the print 
server. 

08 LAN ERROR - 
INFINITE DEFERRAL

There is a network congestion problem. 

Note: 

If the print server is not connected to the network, this 

error cannot occur.

08 AUTHENTICATION 
IN PROGRESS

Link-level authentication is in progress. 

09 LAN ERROR - 
BABBLE

Check the network connections. If the connections are 
intact, run the power-on self-test: turn the printer off, then 
on again. If the error persists, replace the HP Jetdirect print 
server. For replacement instructions, see the hardware 
installation guide for your print server.

0A LAN ERROR - 
NO SQE

(Wired Ethernet) Check the network connections. If the 
connections are intact, run the power-on self-test: turn the 
printer off, then on again. If the error persists, replace the 
HP Jetdirect print server. 

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Canon image Prograf iPF785 Series Basic Manual preview
image Prograf iPF785 Series
Brand: Canon Pages: 136
Unisys ES5000 Manual preview
ES5000
Brand: Unisys Pages: 20
GBC A1 Operation & Instruction Manual preview
A1
Brand: GBC Pages: 110
Xerox M Series Initial Setup Card preview
M Series
Brand: Xerox Pages: 2
WaxJet 6100 Service Reference Manual preview
6100
Brand: WaxJet Pages: 131
Samsung ML-2240 - 23 Ppm Mono Laser Printer Manual Del Usuario preview
ML-2240 - 23 Ppm Mono Laser Printer
Brand: Samsung Pages: 82
Samsung ML-2150 Servicing Precautions preview
ML-2150
Brand: Samsung Pages: 8
Samsung ML-1610 - B/W Laser Printer User Manual preview
ML-1610 - B/W Laser Printer
Brand: Samsung Pages: 134
Samsung ML-1610 - B/W Laser Printer Manual Del Usuario preview
ML-1610 - B/W Laser Printer
Brand: Samsung Pages: 112
Samsung ML-1210 Manual Del Usuario preview
ML-1210
Brand: Samsung Pages: 128
Samsung ML ML-4551N Manual Del Usuario preview
ML ML-4551N
Brand: Samsung Pages: 152
Samsung ML 3471ND - B/W Laser Printer User Manual preview
ML 3471ND - B/W Laser Printer
Brand: Samsung Pages: 207
Samsung ML 2150 - B/W Laser Printer Manual Del Usuario preview
ML 2150 - B/W Laser Printer
Brand: Samsung Pages: 237
Samsung ML 3471ND - B/W Laser Printer Manual Del Usuario preview
ML 3471ND - B/W Laser Printer
Brand: Samsung Pages: 103
Samsung ML 2150 - B/W Laser Printer User Manual preview
ML 2150 - B/W Laser Printer
Brand: Samsung Pages: 217
Samsung ML-2010 - B/W Laser Printer Manual Del Usuario preview
ML-2010 - B/W Laser Printer
Brand: Samsung Pages: 122
Samsung SCX-5315F Service Manual preview
SCX-5315F
Brand: Samsung Pages: 103
Samsung ML-2010 - B/W Laser Printer Manual preview
ML-2010 - B/W Laser Printer
Brand: Samsung Pages: 25

Brands by name

Popular brands

Load more brands