HP Jetdirect J7949e Administrator'S Manual Download

Page: 74 / 232

ENWW

TCP/IP Configuration 74

sys-location

Alpha-numeric string (up to 255 characters), typically used
to identify a location.

sys-contact

Alpha-numeric string (up to 255 characters), typically used
to identify the name of a network or device administrator.

ssl-state

Sets the print server’s security level for Web
communications:

1: Forced redirection to the HTTPS port. Only HTTPS
(secure HTTP) communications can be used.

2: Disable forced redirection to HTTPS. Both HTTP and
HTTPS communications can be used.

security-reset

Reset security settings on the print server to factory default
values. 0 (default) does not reset, 1 resets the security
settings.

TCP/IP Main

Command

Description

host-name

Alphanumeric string (up to 32 characters), to assign or
change the name of the network device. For example,

“host-name printer1” assigns the name “printer1” to the

device. The default host name is NPIxxxxxx, where xxxxxx
are the last six digits of the LAN hardware (MAC) address.

ip-config Specify

the

configuration method:

manual

: The print server will wait for IP parameters using

manual tools (such as Telnet, embedded Web server,
control panel, installation/management software). Status
will be

User Specified

bootp

: The print server will send BOOTP requests on the

network for dynamic IP configuration.

dhcp

: The print server will send DHCP requests on the

network for dynamic IP configuration.

auto_ip

: The print server will be automatically configured

with a unique link-local address 169.254.x.x.

IP address for the print server, in dotted notation. For
example:

ip-config manual

ip 192.168.45.39

where

ip-config

specifies manual configuration and

manually sets the IP address 192.168.45.39 on the print
server.

Specifying 0.0.0.0 clears the IP address.

If you exit and save a new IP address, it must be specified
on the next Telnet connection.

Table 3.4

Telnet Commands and Parameters (2 of 13)

Summary of Contents for Jetdirect J7949e









































































































































































































































Search results

Summary of Contents for Jetdirect J7949e

Reviews:

Related manuals for Jetdirect J7949e

Brands by name

Popular brands

HP Jetdirect J7949e, Administrator'S Manual

Search results

Summary of Contents for Jetdirect J7949e

Reviews:

Related manuals for Jetdirect J7949e

Brands by name

Popular brands