HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 180 / 232

background image

ENWW

HP Jetdirect Configuration Page 180

Configuration Page Messages

HP Jetdirect Configuration/General Information

Information in this section provides general HP Jetdirect print
server configuration as described in

Table 9.1

. For error messages,

see

Table 9.9

.

Table 9.1

HP Jetdirect Configuration (1 of 2)

Message

Description

STATUS:

Current state of the HP Jetdirect print server.

I/O CARD READY: The HP Jetdirect print server has
successfully connected to the network and is awaiting data.

I/O CARD INITIALIZING: The HP Jetdirect print server is
initializing the network protocols. For more information, see
the status line for each protocol on the configuration page.

I/O CARD NOT READY: There is a problem with the print
server or its configuration.

An error code and message is displayed if the print server
is not ready. For more information, see

Table 9.9

.

MODEL NUMBER:

The model number of the HP Jetdirect print server (for
example, J7949E).

HARDWARE
ADDRESS:

The 12-digit hexadecimal network hardware (MAC) address
of the HP Jetdirect print server installed in the printer or
device. This address is assigned by the manufacturer.

FIRMWARE VERSION: The firmware revision number of the HP Jetdirect print

server currently installed in the printer.

PORT SELECT:

(Ethernet only) Specifies the port on the HP Jetdirect print
server that has been detected for use:

NONE: The print server is not connected to the network.

RJ-45: The RJ-45 network port is connected.

LAA

The Locally Administered Address (LAA) identifies the
user-specified LAN hardware address of a print server,
which may be required by some network adiministrators.
The default address is the print server’s factory-default LAN
hardware address.

«
...
178
179
180
181
182
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Brand: IESC Pages: 109

Brand: Dascom Pages: 146

Brand: MSI Pages: 106

Brand: Protogate Pages: 30

Brand: Canon Pages: 189

Brand: Canon Pages: 293

Brand: Canon Pages: 341

Brand: Canon Pages: 387

Brand: Canon Pages: 396

Brand: Canon Pages: 465

Pixma TR7800 Series

Brand: Canon Pages: 554

Brand: Canon Pages: 460

Brand: Canon Pages: 498

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brand: IBM Pages: 106

x3200 - System M3 - 7328

Brand: IBM Pages: 100

System x3400 Type 7975

Brand: IBM Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands