HP Jetdirect J7949e Administrator'S Manual Download

Page: 8 / 232

ENWW

Introducing the HP Jetdirect Embedded Print Server 8

Supported Network Protocols

The supported network protocols, and popular network printing
environments that use those protocols, are listed in

Table 1.1

If not supplied with this product, HP network setup and
management software for supported systems may be obtained from
HP support at:

http://www.hp.com/support/net_printing

For software to set up network printing on other systems, contact
your system vendor.

Table 1.1

Supported Network Protocols

Supported Network
Protocols

Network Printing Environments*

TCP/IP

Microsoft Windows 98/Me/NT4.0/2000/XP (32- and 64-bit),
Direct Mode printing

Novell NetWare 5, 6.x using NDPS

UNIX and Linux, including:

Hewlett-Packard HP-UX, Sun Microsystems Solaris
(SPARCsystems only), IBM AIX**, HP MPE-iX**, RedHat
Linux, SuSE Linux

LPR/LPD (Line Printer Daemon)**

IPP (Internet Printing Protocol)

FTP (File Transfer Protocol)

IPX/SPX and
compatible

Novell NetWare**

Microsoft Windows 98/Me/NT4.0/2000/XP (32-bit only), Direct
Mode printing

AppleTalk

(EtherTalk only)

Apple Mac OS

DLC/LLC

Microsoft Windows NT**

* Refer to the current HP Jetdirect product data sheets for additional network systems
and versions. For operation with other network environments, consult your system
vendor or authorized HP dealer.

** For these network systems, contact your network system vendor for software,
documentation, and support.

Summary of Contents for Jetdirect J7949e









































































































































































































































Search results

Summary of Contents for Jetdirect J7949e

Reviews:

Related manuals for Jetdirect J7949e

Brands by name

Popular brands

HP Jetdirect J7949e, Administrator'S Manual

Search results

Summary of Contents for Jetdirect J7949e

Reviews:

Related manuals for Jetdirect J7949e

Brands by name

Popular brands