HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 170 / 232

background image

ENWW

Troubleshooting the HP Jetdirect Print Server 170

Procedure 3: Resolving Printer Display
Error Messages

Check the following information to resolve network-related error
messages that appear on the printer control panel display.

This

information assumes you have already printed a configuration page.

1. Does the printer’s control panel display a Service Error message,

such as 49.XXXX, 79.XXXX or 8X.XXXX error?

■

Refer to your printer manuals to interpret the error message.

■

If you upgraded the Jetdirect firmware recently, power the
print server off/on using the printer’s On/Off switch.

■

Verify the network cable is properly connected.

■

Inspect and verify the configuration parameters on the
Jetdirect configuration page. To interpret HP Jetdirect
configuration page messages, see

Chapter 9

.

■

Record all error codes and contact your service provider. For
warranty service, include all diagnostic and configuration
pages with the faulty print server.

2. Does

INITIALIZING/DO NOT POWER OFF

or similar message appear

on the display?

Wait for ten minutes to see if it clears. If it does not, you may
need to replace the HP Jetdirect print server.

3. Does a

40 ERROR

appear on the printer’s control panel display?

The HP Jetdirect print server detected a break in the data
communications. When this error occurs, the printer
goes offline.

A break in communications may result from the physical
network connection being disrupted or the server going down.
If your printer has an Auto Continue feature that is disabled or
off, you must press the appropriate key (

Start

or

Pause/Resume

, for example) on the printer after the

communications problem is solved to put the printer back
online. Turning the Auto Continue feature on forces the printer
to reconnect without user intervention. However, this does not
solve the disconnect problem.

«
...
168
169
170
171
172
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

Brand: Magicard Pages: 2

Brand: Magicard Pages: 2

eserver xSeries 440

Brand: IBM Pages: 34

Brand: IESC Pages: 109

Vlinx Serial Servers ESP901E

Brand: B&B Electronics Pages: 92

Brand: Patton electronics Pages: 16

Brand: Oki Pages: 88

Brand: Oki Pages: 40

Brand: Gerber Pages: 163

EuroLine Series

Brand: Output Technology Pages: 73

H SERIES RS/6000

Brand: IBM Pages: 424

Brand: Ubiquiti Pages: 28

Brand: Ascend Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands