HP Jetdirect J7949e Administrator'S Manual Download Page 134 | Manualshive

Page: 134 / 232

background image

ENWW

134

5

Configuring for LPD Printing

Introduction

The HP Jetdirect print server contains an LPD (Line Printer
Daemon) Server module to support LPD printing. This chapter
describes how to configure the HP Jetdirect print server for use
with various systems that support LPD printing. These
instructions include:

●

LPD on UNIX Systems

■

Configuring BSD-based UNIX systems using LPD

■

Configuring print queues using the SAM utility (HP-UX
systems)

●

LPD on Windows NT/2000/Server 2003 Systems

●

LPD on Windows XP Systems

●

LPD on Mac OS Systems

Note

For other systems not listed, refer to your operating
system documentation and online help.

Recent versions of Novell NetWare (NetWare 5.x
with NDPS 2.1 or greater) support LPD printing.
For setup instructions and support, refer to the
documentation supplied with NetWare. Also, refer
to the Technical Information Documentation (TID)
on Novell’s support Web site.

«
...
132
133
134
135
136
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Univerge SV9300

Brand: NEC Pages: 47

Univerge SV9100

Brand: NEC Pages: 766

Brand: Xerox Pages: 532

Brand: Xerox Pages: 174

Brand: Xerox Pages: 5

Brand: Xerox Pages: 3

Brand: Xerox Pages: 9

Brand: Xerox Pages: 12

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: Xerox Pages: 4

Brand: Xerox Pages: 4

Brand: Xerox Pages: 162

Brand: Xerox Pages: 83

Brand: Xerox Pages: 2

Brand: Xerox Pages: 117

Brand: Xerox Pages: 105

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands