HP Jetdirect J7949e Administrator'S Manual Download Page 84 | Manualshive

Page: 84 / 232

background image

ENWW

TCP/IP Configuration 84

AppleTalk

Command

Description

appletalk

Enables or disables AppleTalk (EtherTalk) protocol
operation on the print server. 0 disables, 1 (default) enables.
For example,

appletalk 0

will disable AppleTalk operation

Name

(Read-only parameter) The name of the printer on the
AppleTalk network. A number after the name indicates that
there are multiple devices with this name, and this is the Nth
instance of the name.

Print Type

(Read-only parameter) Specifies the AppleTalk network
printer type reported by the Jetdirect print server. Up to three
print types may be reported.

Zone

(Read-only parameter) The name of the AppleTalk network
zone on which the printer is located.

Phase

(Read-only parameter) AppleTalk phase 2 (P2) is
preconfigured on the HP Jetdirect print server.

Status

(Read-only parameter) Indicates the current AppleTalk
configuration status.

READY: Indicates the HP Jetdirect print server is awaiting
data.

DISABLED: Indicates that AppleTalk was manually
disabled.

INITIALIZING: Indicates that the print server is registering
the node address or name. An additional status message
may also be displayed.

DLC/LLC

Command

Description

dlc/llc-config

Enables or disables DLC/LLC protocol operation on the print
server. 0 disables, 1 (default) enables. For example,

dlc/llc-config 0

will disable DLC/LLC operation.

strict-8022

Controls DLC/LLC protocol interpretation:

0 (default): disables, that is, provides loose interpretation.

1: enables, that is, provides strict interpretation).

Table 3.4

Telnet Commands and Parameters (12 of 13)

«
...
82
83
84
85
86
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

MultiPASS L6000

Brand: Canon Pages: 24

Laser Class 700 Series

Brand: Canon Pages: 221

Univerge SV9100

Brand: NEC Pages: 78

UNIVERGE SL2100

Brand: NEC Pages: 34

Brand: NEC Pages: 2

Brand: NEC Pages: 975

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

Brand: Samsung Pages: 341

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 227

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 118

CLP 300N - Network-ready Color Laser Printer

Brand: Samsung Pages: 94

3561ND - B/W Laser Printer

Brand: Samsung Pages: 252

3561ND - B/W Laser Printer

Brand: Samsung Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands