HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 94 / 232

background image

ENWW

Using the Embedded Web Server 94

access. However, the print server may be configured to appear
as a secure site using an installed X.509-compliant certificate
for identification. When properly configured, encrypted browser
communications through HTTPS (secure HTTP) may be used
for secure access.

Although not recommended, you can use your

Internet

Options

menu to configure your browser to ignore security

warnings if the print server is configured to operate through
HTTPS. See

Mgmt. Protocols

.

4. An embedded Web server page will be displayed.

Operating Notes

●

If you enter or change a configuration parameter value, click

Apply

to enable your change, or click

Cancel

to erase your

change.

●

Changes to the IP address will close the connection to the
embedded Web server. To re-establish a connection, use the new
IP address.

CAUTION

Changes to the IP address on the HP Jetdirect print
server may result in printing failures for clients
that have been configured to print to this printer
using the previous IP address.

●

Novell NetWare networks: On the

Network Settings

page, use

the

IPX/SPX

tab to configure Novell Directory Services (NDS)

Queue Server mode parameters. Note that the embedded Web
server cannot create NDS objects (print server, printer, and print
queue objects) on the Novell server. To create these objects, use
a Novell NetWare utility, such as NWAdmin, or configure the
IPX/SPX stack for NDS through HP utilities, such as the HP
Install Network Printer Wizard or HP Web Jetadmin.

«
...
92
93
94
95
96
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

PIXMA MX882 Series

Brand: Canon Pages: 34

Brand: Canon Pages: 4

Laser Class 700 Series

Brand: Canon Pages: 30

imagePROGRAF iPF9400

Brand: Canon Pages: 8

Brand: Crown Pages: 12

Brand: Ganz Pages: 5

Brand: Xerox Pages: 55

Daisy Wheel 410

Brand: Radio Shack Pages: 140

IMAGE M4100 Series

Brand: G&G Pages: 147

Brand: Commodore Pages: 188

Brand: EcLine Pages: 72

Brand: GCC Technologies Pages: 80

LabeLase 1000Exhaust

Brand: InfoSight Pages: 38

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 4

Brand: Sony Pages: 27

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands