background image

0

WARNING:

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used
in accordance with the instruction manual, may cause interference to radio communications. It has
been tested and found to comply with the limits for a Class A computing device pursuant to Subpart
B of Part 15 of FCC Rules, which are designed to provide reasonable protection against such inter-
ference when operated in a commercial environment. Operation of this equipment in a residential
area is likely to cause interference in which case the user at his own expense will be required to take
whatever measures may be required to correct the interference.

EMC

 

directive

:

This product observes the rules and regulations of the EMC directive. If so required, a declaration of
conformity in local language stipulating the applied rules and regulations can be obtained.

Trademarks:

Company and product names mentioned in this datasheet are trademarks or registered trademarks of
their respective owners.

Rank Xerox Electronic Documentation

Xerox LS 3270

User’s Guide

Doc. no D60322

Revision 01

Solution for Xerox Printers

Get other manuals https://www.bkmanuals.com

Summary of Contents for LS 3270
























































Reviews: