HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 212 / 232

background image

NWW

TCP/IP Overview 212

The syslog server may not receive all syslog events from the
HP Jetdirect print server:

●

UDP does not guarantee delivery of messages.

●

The HP Jetdirect print server attempts to eliminate duplicate
messages (to minimize unnecessary network traffic).

●

The volume of messages sent by the HP Jetdirect print server is
configurable.

Methods to configure HP Jetdirect syslog parameters include
BOOTP, DHCP, Telnet, the embedded Web server, and
management software. For selected printers, a menu
accessed through the printer control panel provides limited syslog
configuration. The syslog configuration command or parameter
entries may vary depending on the method used. For more
information, see the applicable sections in this guide.

Selected syslog parameters on the HP Jetdirect print server are
listed in

Table A.4

.

Table A.4

HP Jetdirect Syslog Parameters

Item

Description

Syslog Server
IP address

IP address of a syslog server for sending syslog messages. If
zero (0.0.0.0) or not specified, syslog messages are disabled.

Syslog Maximum
Messages

The number of syslog messages that can be sent by the
HP Jetdirect print server on a per-minute basis, from 0 to 1000.
This parameter helps to control the syslog file size. The default
is 10 messages per minute. If 0, the number of syslog messages
is not restricted.

Syslog Priority

A method for filtering syslog messages that are sent to the
syslog server. The range is 0 through 8, with 0 the most specific
and 8 the most general. Only messages that are lower than the
specified filter level (or higher in priority) are reported. The
default is 8, messages of all priorities are sent. If 0, all syslog
messages are disabled.

Syslog Facility

A code used to identify the source facility of a message (for
example, to identify the source of selected messages during
troubleshooting). By default, the HP Jetdirect print server uses
LPR as the source facility code, but local user values of local0
through local7 can be used to isolate individual or groups of print
servers.

«
...
210
211
212
213
214
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

imagePROGRAF iPF760

Brand: Canon Pages: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 16

imagePRESS C850

Brand: Canon Pages: 63

imagePROGRAF iPF760

Brand: Canon Pages: 132

imagePROGRAF iPF815

Brand: Canon Pages: 48

Brand: Canon Pages: 56

imagePROGRAF iPF8300

Brand: Canon Pages: 24

imagePROGRAF iPF8300

Brand: Canon Pages: 4

imagePROGRAF iPF6350

Brand: Canon Pages: 12

imagePROGRAF iPF6350

Brand: Canon Pages: 2

imagePROGRAF IPF9000S

Brand: Canon Pages: 184

imagePRESS C800 Series

Brand: Canon Pages: 93

imagePROGRAF iPF815

Brand: Canon Pages: 324

Brand: Panasonic Pages: 169

Brand: Oki Pages: 126

Brand: Xerox Pages: 8

Brand: Oki Pages: 349

Brand: Datacom Pages: 89

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands