HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 47 / 232

background image

ENWW

TCP/IP Configuration 47

TCP/IP Main

host-name:

(sys-name:, name:)

Specifies the node name that will appear on the Jetdirect configuration page.
Default is NPIxxxxxx, where xxxxxx is the last six digits of the LAN hardware
address.

parm-file:

Specifies the path and file name whose contents are sent to the printer for printing
each time the print server is powered on. The path and filename entry is limited to
64 alphanumeric characters.

domain-name:

The domain name for the device (for example, support.hp.com). It does not
include the host name; it is not the Fully Qualified Domain Name (such as
printer1.support.hp.com).

pri-dns-svr:

(dns-srv)

The IP address of the primary DNS (Domain Name System) server.

sec-dns-svr:

The IP address of a secondary DNS server to use if the primary DNS server is
unavailable.

pri-wins-svr:

(pri-wins-srv:)

The IP address of the primary Windows Internet Name Service (WINS) server.

sec-wins-svr:

(sec-wins-srv:)

The IP address of the secondary Windows Internet Name Service (WINS) server.

TCP/IP Print Options

9100-printing:

(9100-config:)

Enables or disables printing to TCP port 9100 on the print server. 0 disables,
1 (default) enables.

ftp-printing:

(ftp-config:, ftp:)

Enables or disables the ability to print through FTP: 0 disables, 1 (default) enables.

ipp-printing:

(ipp-config:, ipp:)

Enables or disables the ability to print through IPP: 0 disables, 1 (default) enables.

Table 3.3

TFTP Configuration File Parameters (2 of 10)

«
...
45
46
47
48
49
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Brand: IBM Pages: 54

BladeCenter HS22

Brand: IBM Pages: 18

Brand: Longshine Pages: 56

Brand: Oki Pages: 2

VarioPrint 6180

Brand: Oce Pages: 306

THERMOMARK CARD

Brand: Phoenix Contact Pages: 35

BullSequana Edge nano

Brand: Atos Pages: 29

Brand: DataCard Pages: 2

Brand: DataCard Pages: 2

Brand: Panasonic Pages: 5

Brand: Panasonic Pages: 6

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 32

TruPhoto AL-TA10U

Brand: Panasonic Pages: 39

SVAP10U - SD PRINTER

Brand: Panasonic Pages: 58

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 62

Brand: Panasonic Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands