HP Jetdirect J7949e Administrator'S Manual Download | Manualshive

Page: 202 / 232

background image

ENWW

HP Jetdirect Configuration Page 202

45 INVALID SYSLOG
ADDRESS

The syslog server IP address specified for the HP Jetdirect
print server (through BOOTP) is an invalid IP address for
specifying a single node. Check your Bootptab file for proper
entries.

46 INVALID SERVER
ADDRESS

The TFTP server IP address specified for the HP Jetdirect
print server (through BOOTP) is an invalid IP address for
specifying a single node. Check your Bootptab file for proper
entries.

47 INVALID TRAP
DEST ADDRESS

One of the SNMP trap (Trap PDU) destination IP addresses
specified for the HP Jetdirect print server (through TFTP) is
an invalid IP address for specifying a single node. Check
your TFTP configuration file.

48 CF ERR - FILE
INCOMPLETE

The TFTP configuration file contained an incomplete last
line that did not end in a newline character.

49 CF ERR - LINE TOO
LONG

A line being processed in the TFTP configuration file was
longer than the HP Jetdirect print server could accept.

4A CF ERR -
UNKNOWN
KEYWORD

A TFTP configuration file line contained an unknown
keyword.

4B CF ERR - MISSING
PARAMETER

A line in the TFTP configuration file was missing a required
parameter.

4C CF ERR - INVALID
PARAMETER

A line in the TFTP configuration file contained an invalid
value for one of the parameters on that line.

4D CF ERR - ACCESS
LIST EXCEEDED

The TFTP configuration file specified too many access list
entries using the “allow:” keyword.

4E CF ERR - TRAP
LIST EXCEEDED

The TFTP configuration file specified too many trap
destination list entries using the “trap-destination:” keyword.

4F TFTP REMOTE
ERROR

The TFTP transfer of the configuration file from the host to
the HP Jetdirect print server failed with the remote host
sending a TFTP ERROR packet to the print server.

50 TFTP LOCAL
ERROR

The TFTP transfer of the configuration file from the host to
the HP Jetdirect print server failed with the local print server
encountering some form of inactivity timeout, or excessive
retransmissions situation.

51 TFTP RETRIES
EXCEEDED

The overall retrying of the TFTP transfer of the configuration
file from the host to the HP Jetdirect print server has
exceeded a retry limit.

Table 9.9

Error Messages (8 of 10)

Error Code and
Message

Description

«
...
200
201
202
203
204
...
»

Summary of Contents for Jetdirect J7949e









































































































































































































































Reviews:

No comments

Related manuals for Jetdirect J7949e

Brand: Chamjin I&C Pages: 21

Brand: Xerox Pages: 12

DocuPrint C3055 DX

Brand: Xerox Pages: 20

PIXMA MG5600 Series

Brand: Canon Pages: 4

Flex System x440 Compute Node

Brand: IBM Pages: 584

Brand: NEC Pages: 10

eServer 342 xSeries

Brand: IBM Pages: 70

Brand: ONELAN Pages: 24

Brand: TYAN Pages: 106

Brand: Ascend Pages: 6

Brand: MIMAKI Pages: 28

Brand: Advantech Pages: 96

TVS-72XU Series

Brand: QNAP Pages: 53

Brand: Citizen Pages: 104

Accel-a-Writer 4

Brand: Xante Pages: 12

Brand: LOYTEC Pages: 4

Brand: RIOT Pages: 18

Brand: Axis Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands