horsch 80910205 Operating Instructions Manual Download Page 121

Page: 121 / 218

12 Using the sprayer

When using the machine pay attention to the notes in chapters

• "Warning signs and other identifications on the machine", from chapter 2.18 - 2.19 and

• "Safety notes for the operator (chapter 2.7 and following)."
paying attention to these notes serves your safety.

WARNING

Danger of breakage during operation, insufficient stability and inadequate steering and brak

ing ability of the Trac if used for purposes other than the ones it is intended for!

Pay attention to the max. payload of the sprayer implement/trailer and the permissible axle and

tongue loads of the Trac. If necessary drive with the tank only partly filled.

WARNING

Danger of crushing, cutting, cutting off, being pulled in, being caught and impact caused by

inappropriate stability and tipping over of the Trac / trailer.

Drive in such a way, that you will at any time be able to securely control the Trac with sprayer imple-

ment and possibly also trailer.

Be aware of your own abilities, account for the road, traffic, sight and weather conditions, the driving

characteristics of the Trac and the influences of the sprayer implement or possibly a trailer.

WARNING

Danger of crushing, shearing, cutting, cutting off, being caught, being pulled in and impact

caused by

•

accidental lowering of lifted, unsecured machine parts.

•

unintended starting and accidental rolling of the Trac or accidental

rolling of Trac/trailer combination.

Secure the Trac against unintended starting and accidental rolling and possibly also the combination

of Trac with trailer against accidental rolling, before you start to rectify any faults on the machine,

Summary of Contents for 80910205



























































































































































































































Search results

Summary of Contents for 80910205

Reviews:

Brands by name

Popular brands

horsch 80910205, Operating Instructions Manual

Search results

Summary of Contents for 80910205

Reviews:

Brands by name

Popular brands