Hitachi P1-00041HFEF, Basic Manual

Page: 63 / 131

4-15
Chapter 4
For parameter configuration
[Ab-01]
～
[Ab-25]
Scaled Output Frequency gain monitor [dA-06]
Code/Name Range (unit) Initial value
Ab-01
Frequency
conversion gain
0.00
～
100.00 1.00
・
The visualized “Scaled Output frequency [dA-06]” is
equal to the “Output frequency [dA-01]” multiplied by the
“Frequency scaling conversion factor[Ab-01]”.
Multispeed command
Code/Name
Range (unit) Initial
value
Ab-03
Multispeed operation
selection
00(16 speeds)/
01(8 speeds)
00
Ab110
Multispeed-0, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-11
Multispeed-1, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-12
Multispeed-2, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-13
Multispeed-3, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-14
Multispeed-4, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-15
Multispeed-5, 1st-motor
0.00 ～ 590.00(Hz)
0.00
Ab-16
Multispeed-6, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-17
Multispeed-7, 1st-motor
0.00 ～ 590.00(Hz)
0.00
Ab-18
Multispeed-8, 1st-motor
0.00
～
590.00(Hz) 0.00
Ab-19
Multispeed-9, 1st-motor
0.00 ～ 590.00(Hz)
0.00
Ab-20
Multispeed-10, 1st-motor 0.00
～
590.00(Hz) 0.00
Ab-21
Multispeed-11, 1st-motor 0.00
～ 590.00(Hz)
0.00
Ab-22
Multispeed-12, 1st-motor 0.00
～
590.00(Hz) 0.00
Ab-23
Multispeed-13, 1st-motor 0.00
～
590.00(Hz) 0.00
Ab-24
Multispeed-14, 1st-motor 0.00
～
590.00(Hz) 0.00
Ab-25
Multispeed-15, 1st-motor 0.00
～
590.00(Hz) 0.00
・
For the 16 speeds selection, set [Ab-03]=03 for
assigning the intelligent terminals 003[CF1] to
006[CF4] makes available the use of the speeds 0 to
15.
Multispeed CF4 CF3 CF2 CF1
Speed 0 OFF OFF OFF OFF
Speed 1 OFF OFF OFF ON
Speed 2 OFF OFF ON OFF
Speed 3 OFF OFF ON ON
Speed 4 OFF ON OFF OFF
Speed 5 OFF ON OFF ON
Speed 6 OFF ON ON OFF
Speed 7 OFF ON ON ON
Speed 8 ON OFF OFF OFF
Speed 9 ON OFF OFF ON
Speed 10 ON OFF ON OFF
Speed 11 ON OFF ON ON
Speed 12 ON ON OFF OFF
Speed 13 ON ON OFF ON
Speed 14 ON ON ON OFF
Speed 15 ON ON ON ON
[Ab210][AC-01]
～
[AC-02]
・
For the 8 speeds selection, set [Ab-03]=01 assigning the
intelligent terminals 007[SF1] to 013[SF7] makes
available the use of the speeds 0 to 7.
Multispeed SF7 SF6 SF5 SF4 SF3 SF2 SF1
Speed 0 OFF OFF OFF OFF OFF OFF OFF
Speed 1 - - - - - - ON
Speed 2 - - - - - ON OFF
Speed 3 - - - - ON OFF OFF
Speed 4 - - - ON OFF OFF OFF
Speed 5 - - ON OFF OFF OFF OFF
Speed 6 - ON OFF OFF OFF OFF OFF
Speed 7 ON OFF OFF OFF OFF OFF OFF
2nd motor
When Intelligent Input terminal 024[SET] is enabled.
Code/Name Range (unit)
Initial
value
Ab210
Multispeed-0, 2nd-motor Same as Ab110
Input method for Acc/Decel time
Code/Name Range (unit)
Initial
value
AC-01
Acceleration/Deceleration
Time input selection
00(Parameter)/
01(Option 1)/
02(Option 2)/
03(Option 3)/
04(Function EzSQ)
00
・
[AC-01] changes the reference target for the Acc/Decel
command.
Individual Acc/Decel for Multispeed
Code/Name Range (unit) Initial value
AC-02
Acceleration/
Deceleration selection
00(Common)/01(Multi) 00
・
When [AC-02]=00, the acceleration/deceleration time
settings [AC120][AC122] or [AC124][AC126] will be in
effect.
・
2-stage acceleration/deceleration functions from
[AC115] to [AC117] can be set.
・
When [AC-02]=01, the acceleration/deceleration time
[AC-30]
～
[AC-88] for each multispeed control (from
speed 1 to 15) are enabled.
・
When [AC-02]=01, while in Multspeed-0 command,
Acc/Decel setting [AC120] [AC122] or Acc/Decel setting
[AC124] [AC126] are enabled.
・
During remote control up/down [FUP]/[FDN]
(parameters [CA-64] and [CA-66]) and PID soft start
(parameter [AH-78]), those parameters can be
overwritten.