manualshive.com logo in svg

HIKVISION Pyronix EURO 280, Programming Manual, Page: 72 / 72

Share
Download
HIKVISION Pyronix EURO 280 Programming Manual Download Page 72

 

Page | 72 

 

QUICK FIND GUIDE 

 

COMMUNICATION 

Function 

Description 

Pages 

SET UP DIGI/SMS? 

Programming of telephone numbers, digi channels 
and SMS details. 

Page: 59 

ENGINEER RESTORE / 
RESET OPTIONS? 

Anti-code and Engineer resets after alarms 

Page: 47 

SET UP 
DOWNLOADING? 

Makes the system available for upload/download via 
a modem or RS232 lead. 

Page: 57 

DIAL OUT MENU? 

Makes the system dial to a PC. 

Page: 67 

ALARM RESPONSE? 

Disable Confirm on Entry, Inputs to Confirm 

Page: 36 

SITE OPTIONS? 

ATE Inputs 

Page: 45 

 

ENGINEER TEST FUNCTIONS 

Function 

Description 

Pages 

ENGINEER TESTS? 

Walk Test, Output test, PHC Communications Test 

Page: 49 

DIAGNOSTICS? 

Readings of the PSU, Input Resistances, etc. 

Page: 52 

 

ADDRESSING DEVICES 

Function 

Description 

Pages 

ASSIGN 
KEYPADS/READERS? 

Address Keypads, Readers, Access Control 

Page: 23 

INSTALL ZEM? 

Address Remote Input Expanders 

Page: 12 

CHANGE OUTPUTS? 

Address Remote Output Expanders 

Page: 38 

 

PROGRAMMING OPTIONS 

Function 

Description 

Pages 

CHANGE INPUTS? 

Programs input types, attributes etc. 

Page: 17 

CHANGE OUTPUTS? 

Programs output types 

Page: 38 

CHANGE TIMERS? 

Programs siren time, confirm time, entry/exit time, 
siren delay etc. 

Page: 29 

CHANGE CODES? 

Programs Duress, Manager & Engineer codes.  

Page: 32 

 

TABLES 

Function 

Description 

Pages 

FAULT CODES 

Fault descriptions 

Page: 68 

INPUT TYPES 

Table of all the input types available 

Page: 17  

OUTPUT TYPES 

Table of all the output types available 

Page: 38 

 

 
 

Summary of Contents for Pyronix EURO 280









































































Reviews:

No comments