manualshive.com logo in svg

HIKVISION Pyronix EURO 280, Programming Manual, Page: 47 / 72

Share
Download
HIKVISION Pyronix EURO 280 Programming Manual Download Page 47

Page | 47 

 

Engineer Reset Options 

The Engineer Reset Options are used so that once an alarm has occurred; the system can only 

be reset by an engineer code, anti-code or red care reset from the alarm-receiving centre.  

Option 

Function 

Engineer 

Restore of 

Intruder 

Following an intruder alarm, an engineer must reset the system before it 
can be used again. Please select ‘UK Intruder’ to enable this, ‘Secure 
Intruder’ should not be used. This will not interfere with the generation of 

an emergency alarm. 

Default = No.

 

Engineer 

Restore of HU 

Following a Hold Up, Input HU or Duress alarm, an engineer must reset 

the system before it can be used again. This will not interfere with the 
generation of a Fire or Gas (emergency) alarm. 

Default = No.

 

Engineer 

Restore of 

Tamper 

Following a Tamper alarm, an engineer must reset the system before it 
can be used again. This will not interfere with the generation of an 

emergency alarm. 

Default = Yes.

 

Engineer 

Restore of 

Soak 

In the event of an input with the ‘soak’, attribute triggering whilst the 
system is set, the system must be reset by an engineer before it can be 

used again. This will not interfere with the generation of an emergency 
alarm. 

Default = No.

 

Engineer 

Restore of 

Confirmed 

Following a confirmed alarm, an engineer must reset the system before it 

can be used again. 

Default = Yes.

 

Engineer 

Restore of 

Faults 

If selected, only an Engineer’s code will be able to reset the following 

faults: ATE telecom fail, Modem fail, ATE single path fail, Telecom line fail, 
Battery disconnect, Batt charge, Batt load, Excessive charge, Battery 
critical, Device fail.

 Default = No. 

Anti-Code 

Restore 

Enables the system to display an anti-code whilst awaiting an Engineer 

reset, which can be used to generate a special reset code. 

Default = No.

 

Engineer Restore Options 

Using the 



and 



keys, scroll to 

‘ENGINEER RESTORE OPTIONS?

’ 

Press the 



key 

 

Eng Restore Int 

Enter 

: for 

No 

Enter 

: for 

UK Intruder 

Press the 



key. 

Repeat the above options for the 
restores: Tamper, Soak, Confirmed, 

and Faults 
(Enter 

: for 

No, 

: for 

Yes

) 

Press the 



key. 

 

Anti-Code Restore 

Enter 

: for 

No 

Enter 

: for 

Yes 

Please note that if Anti-Code is 

selected, this will coincide with the 
options you have selected previously. 

For example, if ‘Engineer Restore 
Intruder’ is selected, and Anti-Code is 

selected, then an anti-code will be 
produced on an Intruder activation. 

You will be returned to the Engineer 
Menu.

 

 

Summary of Contents for Pyronix EURO 280









































































Reviews:

No comments