manualshive.com logo in svg

HIKVISION Pyronix EURO 280, Programming Manual, Page: 10 / 72

Share
Download
HIKVISION Pyronix EURO 280 Programming Manual Download Page 10

 

Page | 10 

 

Inhibit Fire/HU 

This function allows you to select if you would like the EURO system to respond to or inhibit 

Fire

 and 

Hold-Up

 Alarms whilst in the Engineers Menu. 

Using the 



and 



keys, scroll to 

‘

INHIBIT FIRE/HU?

’ 

Press the 



key 

 

The following will be displayed: 

Enter 

: for No 

(Default)

 

Enter 

: for Yes 

 

Press the 

  key 

You will be returned to the Engineer 
Menu. 

 

Software Revision 

This option identifies the software version number, software serial number and product. 

Using the 



and 



keys, scroll to 

‘

SOFTWARE REVISION?

’ 

Press the 

 key. 

 

The version number will be displayed. 

Press the 

 key. You will be returned 

to the Engineer Menu. 

 

Choose Mode 

4.1.1 The End of Line Range 

This programs the panel to operate with different resistor values: 

1K

   = 

Alarm: 1K

, 

Tamper: 1K.  

2K2

 = 

Alarm: 4K7, Tamper: 2K2. 

(Default)

 

4K7

 = 

Alarm: 4K7, Tamper: 4K7.  

4.1.2 SR or DR 

This programs whether the whole alarm panel and any ZEMs will be used in Singe End of Line 

mode (SR) or Double End of Line (DR) resistor mode. 

(DR is selected as default)

 

4.1.3 Input Response Time 

This selects the time that an input trigger must be present before the whole system responds 
by generating an alarm, and is programmable from 100mS (0.1 seconds) to 3000mS (3 

seconds). 

Note: Settings below 400ms do not comply with PD6662/EN50131. 

400ms is

 

selected as default. 

 

Summary of Contents for Pyronix EURO 280









































































Reviews:

No comments