manualshive.com logo in svg

HIKVISION Pyronix EURO 280, Programming Manual, Page: 63 / 72

Share
Download
HIKVISION Pyronix EURO 280 Programming Manual Download Page 63

Page | 63 

 

11 

System Changes/Resets:

 Clock Set From/To, Added/Deleted/Changed Code, System Restart, Twin 

Device, Excess Current, Logs Cleared, Engineer Reset, Clean Start, Site Changed, CHC Call Failed, 

Logs nearly full, PC Clock Set to,  

12 

Manager Info:

 Unset System 

13 

Engineer Info: 

Engineer Access/Exit 

14 

Access Control Alarm:

 Door Left Open/Forced 

15 

Access Control Info:

 Tag at Reader 

16 

Access Control Ref:

 Invalid Tag 

17 

Special Log Switcher On:

 Input Special Log Switcher Open 

18 

Special Log Switcher Off: 

Input Special Log Switcher Closed 

19 

Special Log Other On: 

Input Special Log Open 

20 

Special Log Other Off: 

Input Special Log Close 

21 

Shunt/Ward Set: 

Shunt Opened Ward Set 

22 

Shunt/Ward Unset:

 Shunt Closed Ward Unset/Silenced 

23 

Shunt/Ward Alarm: 

Ward Alarm 

24 

Walk Test:

 Input Walk Tested 

25 

Restores: 

Burglary Restore, Gas Restore, Tamper Restore, Entry/Exit Restore, Tamper on Input 

Restore, Hold Up Restore, iD line short restore, Fuse fail restore, Case Tamper Restore, SAB Tamper 

Restore, Day Alarm Restore, Interior Alarm Restore, Radio Low Battery Restore, Radio Jamming 

Restore, Radio Supervision Restore 

26 Not 

Used 

27 

Mains Fail: 

Mains Fail Alarm/Restore 

28 

Duress: 

Fire Alarm,Hold Up Alarm, Duress Code, Fire Alarm Once, Holdup Alarm Once, Fire Restore, 

PA Restore, Hold Up Restore,  

29 

Emergency:

 Emergency Input Opened, Emergency Alarm Once, Emergency Restore,  

30 

Input Status:

 Input Omitted, Input Force Armed 

31 

Aborts:

 Stopped Set, Abort 

4.1.64 PABX Systems (Only relevant to SMS) 

Please note for PABX telephone systems (where a “9” is needed in order to dial an outside 
line), you must put “NN” before the account number in the “account reference” part of the 

programming (see below). If you haven’t been given an account number then the account 
reference “NN1111” would be OK to use. This needs to be entered on the keypad. 

Program ARC/SMS? 

Using the 



and 



keys, 

scroll to 

‘PROGRAM 

ARC/SMS?

’ 

Press the 



key 

 

To program in an ARC 
number, press the 



key

 

 

Disable ARC/SMS 

: Enabled  

: Disabled 

Press the 



key. 

Use the numeric keys to 

select the ARC details to 
program (up to 4 can be 
selected). Press the 



key 

 

Summary of Contents for Pyronix EURO 280









































































Reviews:

No comments