Gree VERSATI III Series Page 49 Service Manual Download

Page: 49 / 135

Unit Control

has been activated, this function cannot be activated at the same tim

e. When ―

Disinfection

‖ has been

activated, ―

Emergen.mode

‖, ―

Holiday mode

‖, ―

Floor debug

‖ ―

Manual defrost

‖, or ―

Refri. recovery

‖

setting will fail and a window will pop up, saying ―

Please disable the disinfect mode!

‖

● ―

Disinfection

‖ can be activated no matter if the unit is turned on or off. This mode will take priority

over the ―

Hot water

‖ mode.

● When disinfection operation fails, the display panel will tell ―

Disinfection fail!

‖. Then, by pressing

OK it will be cleared.
● When ―

Disinfection

‖ has been activated, if communication error with the indoor unit or malfunction

of the water tank heater occurs, it will automatically quit.
●It will be memorized upon power failure.

3.2.2.10 Clock Timer

[Operation Instructions]

★

At the function setting page, access to

the ―

Clock timer

‖ setting page.

★

At the ―

Clock time

r‖ setting page, it can be set to ―

‖ or ―

Off

‖.

★

The option ―

Mode

‖ is used to time the desired mode; ―

WOT-Heat

‖ and ―T

water tank”

is used to set

the corresponding water temperature; ―

Period

‖ is used to for time setting. After that, by touching the

―

Save

‖ icon, all settings will be saved.

[Notes]
● When ―

Clock timer

‖ has been set and ―

Hot water

‖ mode is involved, in this case, if ―

Water tank

‖ is

changed to ―

Without

‖, ―

Hot water

‖ will be automatically switched to ―

Heat”

, and ―

Cool/Heat + Hot

water

‖ will be switched to ―

Cool/Heat

‖.

● When ―Weekly timer‖ and ―Clock timer‖ have been set at the same time, the priority will be given to the
former.
● When the water tank is available, ―

Heat

‖, ―

Cool

‖, ―

Hot

‖, ‗

Heat + Hot water

‖, and ―

Cool + Hot water

‖

are allowed; however, when the water tank is unavailable, only ―

Heat

‖ and ―

Cool

‖ are allowed.

● When the end time is earlier than the start time, this setting is invalid.

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands