Gree VERSATI III Series Page 60 Service Manual Download

Page: 60 / 135

Unit Control

3.2.4.8 Remote Sensor

[Operation Instructions]

★

At the commissioning parameter setting page, by touching ―

Remote sensor

‖, the control panel will

access to the corresponding setting page, where it can be set to ―

With

‖ or ―

Without

‖.

[Notes]
●This setting will be memorized upon power failure.
●Only when ―

Remote sensor

‖ is set to ―

With

‖, the ―

Ctrl. State

‖ can be set to ―

T-room

‖.

3.2.4.9 Air Removal

[Operation Instructions]

★

At the commissioning parameter setting page, by touching ―

Air removal

‖, the control panel will access

to the corresponding setting

page, where it can be set to ―

‖ or ―

Off

‖.

[Notes]
● This setting will be memorized upon power failure.
● This setting can be done only when the unit is turned off. And when it is set to ―

‖, the unit is not

allowed to be turned on.

3.2.4.10 Floor Debug

[Operation Instructions]

★

1. At the commissioning parameter setting page, by touching ―

Floor debug

‖, the control panel will

access to the corresponding setting page.

★

2. At the setting page, ―

Floor debug

‖, ―

Segments

‖, ―

Period 1 temp

‖, ―

Segment time

‖, and ―

ΔT of

segment

‖ can be set.

No.

Full Name

Displayed Name

Range

Default

Accuracy

Floor debug switch

Floor debug

On/Off

Off

Quantity of segments

Segments

1~10

Temperature of the first

Period 1 temp

25~35

℃

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands