Gree VERSATI III Series Page 43 Service Manual Download

Page: 43 / 135

Unit Control

Error Icon

[Notes]
●At any other page, where there is no operation in 10 minutes, the display panel will back to the menu
page.

3.1.2 Backlight

Among the general setting page, when ―Back light‖ is set to ―Energy save‖, the display panel will light

off when there is no operation in 5 minutes. However, it will light on again by touching any valid area.

When ―Back light‖ is set to ―Lighted‖, the display panel will be kept lighting on.
It is suggested to set it to ―Energy save‖ so as to extend its service life,

3.2 Operation Instructions

3.2.1 ON/OFF

[Operation Instructions]

★

At the menu page, by touching ON/OFF, the unit will be turned on/off.

[Notes]
●It is defaulted to be OFF upon first power-on.
●ON/OFF operation will be memorized by setting ―

On/Off Memory

‖ to be ―

‖ at the ―

GENERAL

.‖

setting page. That is, in case of power failure the unit will resume running upon power recovery. Once

“On/off Memory

‖ is set to be ―

Off

‖, in case of power failure the unit will keep ―

Off

‖ upon power recovery.

ON Page

3.2.2 Function Setting

[Operation Instructions]

★

1. At the menu page, by

touching ―

FUNCTION

‖, it will go to the function setting page as shown in the

figure below.

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands