Gree VERSATI III Series Service Manual Download

Page: 37 / 135

Unit Control

1.2 Control Flowchart

2 Main Control Logics

2.1 Cooling

2.1.1 Control to the Compressor

When the unit is controlled by the leaving water temperature, the operating frequency of the

compressor will be adjusted by the temperature difference in the way that it increases as the

temperature difference goes up and it decreases as the temperature difference goes down.

(Temperature difference= actual leaving water temperature-leaving water temperature set point).

2.1.2 Freeze Protection

When it is detected that the leaving water temperature of the plate heat exchanger is lower than the

freeze protection temperature, the compressor will drop its operating frequency until it reaches the

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands