Gree VERSATI III Series Service Manual Download Page 109

Page: 109 / 135

Installation

4.17 Wiring of the Thermostat

Installation of the thermostat is very similar to that of the remote air temperature sensor.

How to Wire Thermostat

(1) Uncover the front cover of indoor unit and open the control box ;

(2) Identify the power specification of the thermostat,it is 230V, find terminal block XT4 as

NO.23~26;

(3) If it is the heating/cooling thermostat, please connect wire as per the figure above.

CAUTION!

①

220V power supply can be provided to the thermostat by the Versati III heat pump.

②

Setting temperature by the thermostat(heating or cooling) should be within the temperature

range of the product ;

③

For other constrains, please refer to previous pages about the remote air temperature sensor;

④

Do not connect external electric loads. Wire 220V AC should be used only for the electric

thermostat;

⑤

Never connect external electric loads such as valves, fan coil units, etc. If connected, the

mainboard of the unit can be seriously damaged;

⑥

Installation of the thermostat is very similar to that of the remote air temperature sensor.

4.18 Wiring of the Control

Notes:

①

The wired controller can be connected to the terminal of AP1 CN4 with the four-wire

communication cable.

Monobloc

Unit

AP1

CN4

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Brands by name

Popular brands