Gree VERSATI III Series Page 68 Service Manual Download

Page: 68 / 135

Unit Control

board

AC contactor protection or input over-zero error AC contactor

Temperature drift protection

Temp. drift

Sensor connection protection ( the current

sensor fails to be connected with the

corresponding phase U and or phase V)

Sensor con.

Communication error between the display

panel and the outdoor unit

ODU Com.

Refrigerant vapor line temperature sensor error Temp RGL

Refrigerant liquid line temperature sensor error

Temp RLL

3.2.5.4 Error Log

[Operation Instructions]

★

At the ―

VIEW

‖ page, by touching ―

Error log

‖, the control panel will go to the error log page, where it is

able to view error records.

[Notes]:
● The error log can accommodate up to 20 pieces of error. Name and occurrence time are available for
each error.
● When error log exceeds 20, the latest will supersede the earliest.

3.2.5.5 Version Viewing

[Operation Instructions]

★

At the ―

VIEW

‖ page, by touching ―

Version

‖, the control panel will go to the version view page, where

it is able to view both the program version and protocol version.

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands