Gree VERSATI III Series Service Manual Download

Page: 84 / 135

Installation

1.1 Installation Position

(1) Avoid direct sunshine.

(2) Must be installed on a firm and solid support.

(3) Ensure the hanger rod, ceiling and building structure have sufficient strength to support the

weight of air conditioner unit.

(4) Avoid placing the unit under window or between two constructions, hence to prevent normal

operating noise from entering the room.

(5) Air flow at inlet and outlet shall not be blocked.

(6) Install at a well-ventilated place, so that the machine can absorb and discharge sufficient air.

(7) Do not install at a place where inflammable or explosive goods exist or a place subject to severe

dust, salty fog and polluted air.

(8) Drainage pipe is easy to connect out.

(9) Do not install at a place where inflammable or explosive goods exist or inflammable or explosive

gas might leak.

(10) Do not install at a place subject to corrosive gas, severe dust, salty fog, smoke or heavy

moisture.

1.2 Matters Need Attention

(1) The installation of unit must be in accordance with national and local safety codes.

(2) Installation quality will directly affect the normal use of air conditioner unit. The user is prohibited

from installation by himself. Please contact your dealer after buying this machine. Professional

installation workers will provide installation and test services according to installation manual.

(3) Do not connect to power until all installation work is completed.

Summary of Contents for VERSATI III Series








































































































































Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands

Gree VERSATI III Series, Service Manual

Search results

Summary of Contents for VERSATI III Series

Reviews:

Related manuals for VERSATI III Series

Brands by name

Popular brands