Gree GMV5 Series Service Manual Download Page 193

Page: 193 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

189

Troubleshooting:

2.3.4.49 “dA” IDU network address error

Error display:

IDU wired controller and IDU receive light board will display

Error judgment condition and method:

Through testing the IDU address chip and IP address, if address chip cannot be read, IDU IP is 0 or

IP is in conflict, report the error.

Possible reason

：

■ODU allocated address is wrong

■IDU treatment is wrong

■Address chip is abnormal

Troubleshooting:

2.3.4.50 “dH” wired controller circuit board error

Error display:

IDU wired controller and IDU receive light board will display

Error judgment condition and method:

Wired controller IIC communication is abnormal

Possible reason

：

Summary of Contents for GMV5 Series


































































































































































































































































































































Search results

Summary of Contents for GMV5 Series

Reviews:

Related manuals for GMV5 Series

Brands by name

Popular brands

Gree GMV5 Series, Service Manual

Search results

Summary of Contents for GMV5 Series

Reviews:

Related manuals for GMV5 Series

Brands by name

Popular brands