Gree GMV5 Series Service Manual Download Page 20

Page: 20 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

6.2 Circuit diagram of GMV

-Y96WM/C-

F(U) and GMV

-Y120WM/C-

F(U)

NOTICE!

This drawing is just for reference; please always refer to the electric wiring stuck to the

unit for actual wiring.

When conducting maintenance based on above circuit diagrams, units must be power-off. Please

strictly following the circuit diagrams when reconnecting the wires, otherwise, electric shock may occur.

7 UNIT OPERATING TEMPERATURE

Cooling

Ambient temperature: -5ºC(23ºF)~52ºC(125.6ºF)

Heating

Ambient temperature: -20ºC (-4ºF)~24ºC (75.2ºF)

In the case of a full fresh air conditioning IDU, the unit operating temperature is as follows:

Cooling

Ambient temperature: 16ºC(60.8ºF)~45ºC(113ºF)

Heating

Ambient temperature: -7ºC (19.4ºF)~16ºC (60.8ºF)



If unit operates out of the above range, it may not work stably and components may even be

damaged.

Summary of Contents for GMV5 Series


































































































































































































































































































































Search results

Summary of Contents for GMV5 Series

Reviews:

Brands by name

Popular brands

Gree GMV5 Series, Service Manual

Search results

Summary of Contents for GMV5 Series

Reviews:

Brands by name

Popular brands