manualshive.com logo in svg

Gree GMV5 Series, Service Manual, Page: 301 / 321

Share
Download
Gree GMV5 Series Service Manual Download Page 301

GREE                                               Photovoltaic Direct-driven Inverter Multi VRF Units 

297 

 

The part 

combining 

the building 

with 

photo-voltaic 

system   

Angle of the photo-voltaic cell 

array   

 

 

 

Overall situation of the building 

 

 

 

Waterproof of the rooftop 

 

 

 

Anchoring structure of the 

photo-voltaic system 

 

 

 

Stressed part of the building 

 

 

 

Surrounding of the photo-voltaic 

system   

 

 

 

 

 

Record of Maintenance 

 

Project name 

 

Contents 

 

 

 

 

 

 

 

                         Issuer:          Date: 

Results 

 

 

 

 

 

 

                          Maintainer:         Date: 

Acceptance 

inspection   

 

 

 

 

                           Inspector:            Date:           

 

Record of Acceptance Inspection

 

Project name 

 

Contents 

 

 

 

 

 

 

 

 

                          Issuer:            Date: 

Results 

 

 

 

 

           

                          Maintainer:          Date: 

Acceptance 

inspection 

 

 

 

 

 

                            Inspector:            Date:           

 
In the Photo-voltaic Direct-Driven Inverter Multi VRF System, the main parts of photo-voltaic system 

should be well-maintained, including the photo-voltaic cell array, photo-voltaic anti-lightning combining 
box, AC power distribution cabinet, and wires and cables between photo-voltaic parts. Most of the items 
of regular inspection on the photo-voltaic system relate to the operation and maintenance of these main 
parts, as described below.   

3.5.1 Photo

-voltaic Cell Array 

3.5.1.1 Operation and maintenance of photo-voltaic parts 

Operation and maintenance of photo-voltaic parts should comply with the following requirements:   
1 The surface of photo-voltaic parts should be kept clean. If you want to clean the surface, please 

note that:   

Summary of Contents for GMV5 Series


































































































































































































































































































































Reviews:

No comments