manualshive.com logo in svg

Gree GMV5 Series, Service Manual

Share
Download
Gree GMV5 Series Service Manual Download Page 121

GREE                                         Photovoltaic Direct-driven Inverter Multi VRF Units 

117 

2.3.2 Pre

-

commissioning Check

 

Installation environment check covers the heat exchange environment of unit and electromagnetic 

radiant components. All requirements should comply with national and local electrical standards. For any 
installation incompliance, records should be made for providing an analysis basis during refrigerating 
system testing. 

2.3.2.1 Installation Appearance Check 

Installation appearance check covers whether pipeline installation complies with specifications, 

whether refrigerant pipes and condensing drainage pipes are thermal insulated, and whether   

Refrigerant pipes should be tidily installed, with outdoor and indoor disperse pipes leaning in the 

required scope. For any installation incompliance, records should be made for providing an analysis 
basis during refrigerating system testing. 

Refrigerant pipes and condensing drainage pipes should not be exposed. If any pipe is exposed, an 

immediate amendment is required to avoid serious loss. 

2.3.2.2 Refrigerating System Check 

1) Before commissioning, make sure that the stop valve of each module reaches the maximum 

opening degree. Check whether there is any refrigerator oil leakage around the valve. If there is, 
immediately check for leakage with soap bubbles or leak detectors. If confirming that leakage 
exists, immediately stop commissioning and solve the problem before continuing commissioning. 

Does the stop valve of 

outdoor unit reach the 

maximum opening 

degree?

 

Oil

leakage?

 

2) Check system refrigerants before startup 
Before the system is started, connect the liquid-tube valve of ODU with a high pressure gauge and 

the air-tube valve of ODU with a low pressure gauge, and then read their values. In this case, high 
pressure and low pressure of the system should be in balance status, and the difference between the 
saturation temperature corresponding to the balanced pressure value and the environment temperature 
(the higher in outdoor and indoor temperatures is taken as environment temperature) should not be 
larger than 5°CK. If the difference is larger than 5°C K, it is required to check the ODU for leakage.   

NOTE: 

Guarantee that the system has never been started before this test. Otherwise, the high 

pressure value will be over-higher than the environment temperature or the low pressure value will be 
over-lower than the environment temperature.   

Summary of Contents for GMV5 Series


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands