manualshive.com logo in svg

Gree GMV5 Series, Service Manual

Share
Download
Gree GMV5 Series Service Manual Download Page 242

GREE                                               Photovoltaic Direct-driven Inverter Multi VRF Units 

238 

Troubleshooting:

 

 

2.3.4.103 “L9” Group-controlled IDU quantity inconsistency 

Err

or display: 

IDU wired controller and IDU receive light board will display 

 

Error judgment condition and method:

 

If the IDU quantity connected with wired controller exceeds 16 sets or actually connected IDU 

quantity is inconsistent with the set group-controlled IDU quantity. 

Possible reason

：

 

■IDU quantity connected with one wired controller exceeds 16 sets;

 

■Actually connected IDU quantity is inconsistent with the set group

-controlled IDU quantity. 

Troubleshooting:

 

 

2.3.4.104“LA” Group-controlled IDU series inconsistency 

Erro

r display: 

IDU wired controller and IDU receive light board will display 

 

Error judgment condition and method:

 

Wired controller detects that the IDUs connected with itself belong to different series. 

Possible reason

：

 

■IDUs connected with one wired control

ler belong to different series. 

Troubleshooting:

 

Summary of Contents for GMV5 Series


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands