Gree GMV5 Series Service Manual Download Page 296

Page: 296 / 321

GREE Photovoltaic Direct-driven Inverter Multi VRF Units

292

3.3.5 Disassembly and Assembly of Gas Liquid Separator

Removal procedure of gas liquid separator

Note: Before removing the gas liquid separator, make sure no refrigerant is inside the pipeline and

power has been disconnected.

Step

Diagram

Operation Procedure

．

Loosen the

hooks at the

bottom of the

electric box and

the screws.

●Remove the upper and lower

front panels;

●Loosen the hooks at the bottom

of the electric box;

● Use a screwdriver to unscrew

the electric box.

2. Remove the

electric box.

●

Disconnect internal and

external connection wires of the

electric box;

●Protect the internal parts during

the disassembly.

3. Disassemble

the gas liquid

separator.

●Heat the 2 connection pipes of

the gas liquid separator by

acetylene welding and then

remove the pipes. Note: Avoid

nearby parts from being burnt

during welding.

4. Remove the

gas liquid

separator.

●Unscrew and remove the gas

liquid separator.

Summary of Contents for GMV5 Series


































































































































































































































































































































Search results

Summary of Contents for GMV5 Series

Reviews:

Brands by name

Popular brands

Gree GMV5 Series, Service Manual

Search results

Summary of Contents for GMV5 Series

Reviews:

Brands by name

Popular brands