manualshive.com logo in svg

GE Multilin 469, Instruction Manual

The "Paradox 469" Reference and Installation Manual is a comprehensive guide for users looking to optimize their product experience. Providing step-by-step instructions and detailed explanations, this manual is available for download free of charge from manualshive.com. Quickly access the manual to unlock the full potential of your Paradox 469 device today.

Share
Download
background image

I–2

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER I: 

A2 METERED DATA........................................................................................................... 6-11
A3 LEARNED DATA ........................................................................................................... 6-27
A4 MAINTENANCE ............................................................................................................ 6-30
A5 EVENT RECORDER ...................................................................................................... 6-33
A6 PRODUCT INFO ........................................................................................................... 6-36

ALARM RELAY

see 4 ALARM RELAY

ALARM STATUS

.......................................................................................................... 6-7

, 

6-8

ALARMS

................................................................................................................................. 5-6

ALIGN START CONTROL RELAYS

............................................................................... 5-20

ALTERNATE WIRING FOR CONTACTORS

................................................................ 3-24

AMBIENT RTD

......................................................................................................... 5-70

, 

5-74

AMBIENT RTD TRIPS

....................................................................................................... 6-30

ANALOG I/O TESTING

...................................................................................................... 7-8

ANALOG IN DIFF 1-2

...................................................................................................... 5-95

ANALOG IN DIFF 3-4

...................................................................................................... 5-96

ANALOG IN MIN/MAX

.................................................................................................... 6-29

ANALOG INPUTS

actual values .................................................................................................................... 6-15
analog in diff 1-4 ............................................................................................................ 5-95
analog in diff 3-4 ............................................................................................................ 5-96
analog in min/max ......................................................................................................... 6-29
analog input minimums/maximums .......................................................................... 5-24
clearing analog input data ........................................................................................... 5-15
description ............................................................................................................. 3-19

, 

5-94

difference setpoints ............................................................................................ 5-95

, 

5-96

maximums ........................................................................................................................ 6-29
minimums ......................................................................................................................... 6-29
setpoints............................................................................................................................ 5-93
specifications ..................................................................................................................... 2-6
testing .......................................................................................................................... 7-8

, 

7-9

trip counters ..................................................................................................................... 6-31

ANALOG OUTPUTS

description ........................................................................................................................ 3-19
operating........................................................................................................................ 5-101
setpoints............................................................................................................................ 5-91
specifications ..................................................................................................................... 2-7
testing .............................................................................................................5-101

, 

7-8

, 

7-9

ANSI DEVICE NUMBERS

.................................................................................................. 2-1

APPARENT POWER

actual values .................................................................................................................... 6-14
specifications ................................................................................................................... 2-12

APPARENT POWER DEMAND

...................................................................................... 6-15

APPLICATION EXAMPLE

................................................................................................ 1-17

APPLICATION NOTES

current transformers ....................................................................................................... A-6

APPLICATIONS

.................................................................................................................... 2-2

ASSIGNABLE DIGITAL INPUTS

.................................................................................... 5-25

ASYMMETRICAL CURRENT

........................................................................................... 5-60

AUXILIARY RELAY

see 2 AUXILIARY RELAY and 3 AUXILIARY RELAY

AVERAGE MOTOR LOAD

...................................................................................... 5-9

, 

6-28

AVERAGE PHASE CURRENT

......................................................................................... 6-11

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

resideo Protectorelay Installation Instructions Manual preview
Protectorelay
Brand: resideo Pages: 8
6TL YAV91074 Technical Manual preview
YAV91074
Brand: 6TL Pages: 25
Schrack LSD2 Series Operating Instructions preview
LSD2 Series
Brand: Schrack Pages: 4
Vimar 0170/001 Quick Start Manual preview
0170/001
Brand: Vimar Pages: 2
Robertshaw 83939-D Series Manual preview
83939-D Series
Brand: Robertshaw Pages: 4
Robertshaw 83939-E1 Manual preview
83939-E1
Brand: Robertshaw Pages: 4
Ampcontrol IPM V2 User Manual preview
IPM V2
Brand: Ampcontrol Pages: 83
F&F FW-R1D Manual preview
FW-R1D
Brand: F&F Pages: 8
Bitron Video RU 60 Connection Instructions preview
RU 60
Brand: Bitron Video Pages: 2
IDEC SmartAXIS FT9Z-1A01 User Manual preview
SmartAXIS FT9Z-1A01
Brand: IDEC Pages: 393
Eaton EMR4-RDC-1-A Instruction Leaflet preview
EMR4-RDC-1-A
Brand: Eaton Pages: 3
ABB REJ 527 Operator'S Manual preview
REJ 527
Brand: ABB Pages: 36
Omron G9SX-ADA222-T Series User Manual preview
G9SX-ADA222-T Series
Brand: Omron Pages: 2
Omron G9SA-301 User Manual preview
G9SA-301
Brand: Omron Pages: 2
Omron G7SA Datasheet preview
G7SA
Brand: Omron Pages: 6
Omron G9SB Datasheet preview
G9SB
Brand: Omron Pages: 8
Omron J7TKN - Datasheet preview
J7TKN -
Brand: Omron Pages: 10
Omron K6EL Manual preview
K6EL
Brand: Omron Pages: 12

Brands by name

Popular brands

Load more brands