GE Multilin 469 Instruction Manual Download | Manualshive

Page: 98 / 338

background image

4–8

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 4: INTERFACES

MESSAGE

X

key, followed by the

MESSAGE

T

key, to scroll through the messages. For

additional information and a complete list of diagnostic messages, refer to

on page 6–37.

4.1.8

Self-Test Warnings

The 469 relay performs self test diagnostics at initialization (after power up) and
continuously as a background task to ensure the hardware and software is functioning
correctly. Self-test warnings indicate either a minor or major problem. Minor problems are
problems that does not compromise motor protection. Major problems are very serious
problems that compromise all aspects of relay operation. Upon detection of either a minor
or a major problem the relay will:

• De-energize the self-test warning relay
• Light the self-test warning LED
• Flash a diagnostic message periodically on the display screen

Table 4–1: Self-Test Warnings

Message

Severity

Failure description

Self-Test Warning 1

Replace Immediately

Major

Caused by detection of a corrupted location in the

program memory as determined by a CRC error

check. Any function of the relay is susceptible to

malfunction from this failure.

Self-Test Warning 2

Replace Immediately

Major

Caused by a failure of the analog to digital

converter A/D1. The integrity of system input

measurements is affected by this failure.

Self-Test Warning 3

Replace Immediately

Major

Caused by a failure of the analog to digital

converter A/D2. The integrity of system input

measurements is affected by this failure.

Self-Test Warning 5

Replace Immediately

Major

Caused by out of range reading of self-test

RTD 13. The integrity of system input

measurements is affected by this failure.

Self-Test Warning 6

Replace Immediately

Major

Caused by out of range reading of self-test

RTD 14. The integrity of system input

measurements is affected by this failure.

Self-Test Warning 7

Replace Immediately

Major

Caused by out of range reading of self-test

RTD 15. The integrity of system input

measurements is affected by this failure.

Self-Test Warning 8

Replace Immediately

Major

Caused by out of range reading of self-test

RTD 16. The integrity of system input

measurements is affected by this failure.

Clock Not Set

Program Date/Time

Minor

Occurs if the clock has not been set.

Unit Temp. Exceeded

Service/CheckAmbient

Minor

Caused by the detection of unacceptably low (less

than -40°C) or high (greater than +85°C)

temperatures detected inside the unit.

Unit Not Calibrated

Replace Immediately

Minor

This warning occurs when the relay has not been

factory calibrated.

«
...
96
97
98
99
100
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: Allen-Bradley Pages: 3

Brand: Sven Pages: 8

Brand: Axis Pages: 21

Brand: BECKWITH ELECTRIC Pages: 450

GreenMAX R1616-1CB

Brand: Leviton Pages: 2

Brand: 6TL Pages: 13

Brand: SafeTrust Pages: 10

Brand: Weidmüller Pages: 2

Brand: Thytronic Pages: 96

Brand: MerCs Pages: 4

Brand: MerCs Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands