GE Multilin 469 Instruction Manual Download Page 260

Page: 260 / 338

6–10

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 6: ACTUAL VALUES

The messages shown here may be used to monitor Digital Input status. This may be useful
during relay testing or during installation.

Note

Digital Input states will read as shorted if assigned as a tachometer.

6.2.7

Real Time Clock

PATH: ACTUAL VALUES

A1 STATUS

REAL TIME CLOCK

The time and date from the 469 real time clock may be viewed here.

MESSAGE

ASSIGNABLE DIGI-

TAL

Range: Open, Shorted

MESSAGE

TRIP COIL

SUPERVISION: No

Range: Coil, No Coil

REAL

TIME

[

]

CLOCK

DATE: 01/01/1994

TIME: 12:00:00

Range: 01 to 12 / 01 to 31 / 1995 to

2094

Summary of Contents for 469



















































































































































































































































































































































Search results

Summary of Contents for 469

Reviews:

Brands by name

Popular brands

GE Multilin 469, Instruction Manual

Search results

Summary of Contents for 469

Reviews:

Brands by name

Popular brands