manualshive.com logo in svg

GE Multilin 469, Instruction Manual

Share
Download
GE Multilin 469 Instruction Manual Download Page 204

5–62

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 5: SETTINGS

For example, if a pump is cooled by the liquid it pumps, loss of load may mean that the 
pump overheats. In this case, enable the undercurrent feature. If the motor loading should 
never fall below 0.75 × FLA, even for short durations, the 

UNDERCURRENT TRIP PICKUP

 

could be set to “0.70” and the 

UNDERCURRENT ALARM PICKUP 

to “0.75”. If the pump is 

always started loaded, the 

BLOCK UNDERCURRENT FROM START

 settings should be disabled 

(programmed as “0”).

The 

UNDERCURRENT ALARM DELAY

 or 

UNDERCURRENT TRIP DELAY

 is typically set as quick 

as possible, i.e. 1 second.

5.7.5

Current Unbalance

PATH: SETTINGS 

ZV

 S6 CURRENT ELEM. 

ZV

 CURRENT UNBALANCE

For the 469 relay, unbalance is defined as the ratio of negative-sequence to positive-
sequence current, 

I

2

/

I

1

, if the motor is operating at a load (

I

avg

) greater than FLA. If the 

motor 

I

avg

 is less than FLA, unbalance is defined as 

I

2

/

I

1

 × 

I

avg

/ FLA. This derating is 

necessary to prevent nuisance alarms when a motor is lightly loaded. If enabled, a trip 
and/or alarm occurs once the unbalance magnitude equals or exceeds the 

CURRENT 

UNBALANCE ALARM(TRIP) PICKUP

 for a period of time specified by the 

CURRENT 

UNBALANCE ALARM(TRIP) DELAY

. If the unbalance level equals or exceeds 40%, or when 

I

avg

 

≥

 25% FLA and current in any one phase is zero, the motor is considered single phasing 

and a trip occurs within 2 seconds. Single phasing protection is disabled if the unbalance 
trip feature is turned “Off”. 

When setting the 

CURRENT UNBALANCE ALARM(TRIP) PICKUP

 level, note that a 1% voltage 

unbalance typically translates into a 6% current unbalance. Therefore, to prevent nuisance 
trips or alarms, the pickup level should not be set too low. Also, since short term 

„

 

CURRENT

[

CURRENT UNBALANCE

ALARM: Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN ALARM 

RELAYS:

Range: Alarm, Alarm & Auxiliary2, 

Alarm & Aux2 & Aux3, 
Auxiliary2, Aux2 & Aux3, 
Auxiliary3

MESSAGE

CURRENT UNBALANCE

ALARM PICKUP: 15%

Range: 4 to 40% in steps of 1

MESSAGE

CURRENT UNBALANCE

ALARM DELAY: 1 s

Range: 1 to 60 s in steps of 1

MESSAGE

CURRENT UNBALANCE

ALARM EVENTS: Off

Range: On, Off

MESSAGE

CURRENT UNBALANCE

TRIP: Off

Range: Off, Latched, Unlatched

MESSAGE

ASSIGN TRIP 

RELAYS:

Range: Trip, Trip & Auxiliary2, Trip & 

Aux2 & Aux3, Trip & Auxiliary3

MESSAGE

CURRENT UNBALANCE

TRIP PICKUP: 20%

Range: 4 to 40% in steps of 1

MESSAGE

CURRENT UNBALANCE

TRIP DELAY: 1 s

Range: 1 to 60 s in steps of 1

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands