GE Multilin 469 Instruction Manual Download | Manualshive

Page: 12 / 338

background image

1–4

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

CHAPTER 1: GETTING STARTED

c.

Learned and last starting capacity.

d. Average motor load.

4.

Maintenance data. This is useful statistical information that may be used for
preventive maintenance. It includes:

a. Trip counters

b. General counter such as number of motor starts, number of emergency restarts,

number of starter operations, digital counter for other purposes not listed above.

c.

Timers such as motor running hours, time between starts timer, and five start tim-
ers used to calculate the average start time of the motor.

5.

RTD Learned Data, which includes the maximum temperature measured by each of
the 12 RTDs.

6.

Event recorder downloading tool.

7.

Product information including model number, firmware version, additional product
information, and calibration dates.

8.

Oscillography downloading tool.

Alarm, trip conditions, diagnostics, and system flash messages are grouped under

Target

Messages

.

Z

Press the

MENU

key to access the header of each menu, which will be

displayed in the following sequence:

To access settings,

Z

Press the

MENU

key until the display shows the header of the Settings

menu.

Z

Press the

MESSAGE

X

or

ENTER

key to display the header for the first

Settings page.
The Settings pages are numbered, have an ‘S’ prefix for easy
identification and have a name which provides a general idea of the
settings available in that page.
Pressing the

MESSAGE

T

and

MESSAGE

S

keys will scroll through all

the available Settings page headers. Settings page headers look as
follows:

SETTINGS

[

Z

]

ACTUAL

VALUES

[

Z

]

TARGET

MESSAGES [

Z

]

«
...
10
11
12
13
14
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: GE Pages: 532

Brand: Pilz Pages: 16

Brand: LOVATO ELECTRIC Pages: 3

Brand: Crouzet Pages: 3

Brand: ABB Pages: 23

Brand: F&F Pages: 2

Brand: F&F Pages: 6

Brand: F&F Pages: 7

Brand: EUCHNER Pages: 4

Brand: Ampcontrol Pages: 41

META MEC Series

Brand: LS Pages: 4

Brand: LEGRAND Pages: 4

Brand: VAMP Pages: 232

Brand: Danfoss Pages: 60

Brand: Keithley Pages: 48

ESR5-BWS-31-24VAC-DC

Brand: Eaton Pages: 22

Brand: Autonics Pages: 5

Brand: Zamel Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands