GE Multilin 469 Instruction Manual Download Page 255

Page: 255 / 338

CHAPTER 6: ACTUAL VALUES

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

6–5

6.2.2

Motor Status

PATH: ACTUAL VALUES

A1 STATUS

MOTOR STATUS

These messages describe the motor status at any given point in time. If the motor has
been tripped and the 469 has not yet been reset, the

MOTOR STATUS

value will be “Tripped”.

The

MOTOR THERMAL CAPACITY USED

reflects an integrated value of both the Stator and

Rotor Thermal Capacity Used. The values for

ESTIMATED TRIP TIME ON OVERLOAD

appear

whenever the 469 picks up on the overload curve.

6.2.3

Last Trip Data

PATH: ACTUAL VALUES

A1 STATUS

LAST TRIP DATA

MOTOR

STATUS

[

]

MOTOR STATUS:

Stopped

Range: Tripped, Stopped, Starting,

Running, Overload

MESSAGE

MOTOR THERMAL

CAPACITY USED: 0%

Range: 0 to 100%

MESSAGE

ESTIMATED TRIP

TIME

Range: 0 to 10000 sec., Never

MESSAGE

MOTOR SPEED:

Low Speed

Range: HIgh Speed, Low Speed. Seen if

two speed motor is enabled

LAST

TRIP

[

]

DATA

CAUSE OF LAST

TRIP:

No Trip to Date

Range: see below

MESSAGE

TIME OF LAST

TRIP:

Range: hour:min:sec

MESSAGE

DATE OF LAST

TRIP:

Range: Month Day Year

MESSAGE

MOTOR SPEED DUR-

ING

Range: High Speed, Low Speed. Seen if

two-speed motor is enabled

MESSAGE

TACHOMETER

PreTrip: 3600 RPM

Range: 0 to 3600 RPM. Seen if a Digital

Input set as Tachometer.

MESSAGE

Range: 0 to 100000 A

MESSAGE

MOTOR LOAD:

0.00 x FLA Pre-

Range: 0.00 to 20.00 x FLA

MESSAGE

CURRENT UNBALANCE

PreTrip: 0%

Range: 0 to 100%

MESSAGE

GROUND CURRENT

PreTrip: 0.00

Range: 0.0 to 5000.0 A. Not seen if

Ground CT is set to “None”.

MESSAGE

Range: 0 to 5000 A. Not seen if

Differential CT is set as None

MESSAGE

HOTTEST STATOR

RTD

Range: –50 to 250°C or –58 to 482°F.

Seen only if at least 1 RTD is set
as Stator

Summary of Contents for 469



















































































































































































































































































































































Search results

Summary of Contents for 469

Reviews:

Brands by name

Popular brands

GE Multilin 469, Instruction Manual

Search results

Summary of Contents for 469

Reviews:

Brands by name

Popular brands