GE Multilin 469 Instruction Manual Download | Manualshive

Page: 97 / 338

background image

CHAPTER 4: INTERFACES

469 MOTOR MANAGEMENT RELAY – INSTRUCTION MANUAL

4–7

Z

To enter a given Settings page, press the

MESSAGE

X

or

ENTER

key.

Z

Press the

MESSAGE

T

or

MESSAGE

S

keys to scroll through sub-page

headers until the required message is reached.
The end of a page is indicated by the message

END OF PAGE

. The

beginning of a page is indicated by

TOP OF PAGE

.

Each page is broken further into subgroups.

Z

Press

MESSAGE

T

or

MESSAGE

S

to cycle through subgroups until the

desired subgroup appears on the screen.

Z

Press the

MESSAGE

X

or

ENTER

key to enter a subgroup.

Each sub-group has one or more associated settings messages.

Z

Press the

MESSAGE

T

or

MESSAGE

S

keys to scroll through settings

messages until the desired message appears.

The majority of settings are changed by pressing the

VALUE

keys until the desired value

appears, and then pressing

ENTER

. Numeric settings may also be entered through the

numeric keys (including decimals). If the entered settings is out of range, the original
settings value reappears. If the entered settings is out of step, an adjusted value will be
stored (e.g. 101 for a settings that steps 95, 100, 105 is stored as 100). If a mistake is made
entering the new value, pressing

ESCAPE

returns the settings to its original value. Text

editing is a special case described in detail in

Entering Alphanumeric Text

Each time a new settings is successfully stored, a message will flash on the display stating

NEW SETTINGS HAS BEEN STORED

.

Z

Press the 4, 6, 9 keys, then press

ENTER

. The following flash message is

displayed:

and the display returns to:

1. Press

ESCAPE

or

MESSAGE

W

to exit the subgroup. Pressing

ESCAPE

or

MESSAGE

W

numerous times will always return the cursor to the top of the

page.

4.1.7

Diagnostic Messages

Diagnostic messages are automatically displayed for any active conditions in the relay
such as trips, alarms, or asserted logic inputs. These messages provide a summary of the
present state of the relay. The Message LED flashes when there are diagnostic messages
available; press the

MENU

key until the relay displays

TARGET MESSAGES

, then press the

PASSCODE

[

ENTER PASSCODE

FOR ACCESS:

NEW SETTINGS

HAS BEEN STORED

SETTINGS ACCESS:

PERMITTED

«
...
95
96
97
98
99
...
»

Summary of Contents for 469



















































































































































































































































































































































Reviews:

No comments

Related manuals for 469

Brand: macromatic Pages: 2

Brand: IFM Pages: 51

MINOTAUR MSR6R/T

Brand: Guard master Pages: 4

Brand: ASO Safety Solutions Pages: 64

Brand: ABB Pages: 152

Brand: GE Pages: 20

Brand: GE Pages: 24

Brand: Fujitsu Pages: 6

Brand: Fujitsu Pages: 7

Brand: Fujitsu Pages: 7

POWR-GARD PGR-4704

Brand: Littelfuse Pages: 14

Brand: Intiel Pages: 3

Brand: GEPA Pages: 9

Brand: Elko Pages: 2

Brand: Elko Pages: 3

Brand: Elko Pages: 4

Brand: Elko Pages: 18

Brand: Elko Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands